I will be giving a presentation in a large dining hall in a couple of weeks. The hall has no screens for projections, and I need to be able to project large enough for people to see from about 80 feet back. Further, the entire East wall is glass with no drapes or other covering, so there will be a lot of ambient light - especially right after lunch at noon.I have a fairly bright projector, but I needed a portable projection screen that gave me at least 9 feet of horizontal display area.I selected the Towond 150" screen after reviewing it and others and checking the comments.This was a good choice.The Towond screen arrived packed in it's carrying case. The black plastic fabric case is 32" long x 6" x 7" with a carrying handle, and is quite light - their data sheet says 11.5 pounds, but it feels lighter.The case contained all the parts, a minimal pictorial instruction sheet (which was sufficient).The screen itself is in a separate, heavy-weight, zip-lock-type bag to protect the soft white polyester screen.Set up was easy by following the directions. The top-bar pieces are individually numbered and shown clearly in the instructions. The two vertical legs need no assembly - just loosen the friction locks and extend the vertical posts. I was able to set up and take down single-handed with no effort.Suggestions for the easy way (IMHO):1. Set up the vertical legs approximately where you want the screen to be located. Loosen the clamp holding the three bracing legs against the center post and extend the bracing legs until the connecting parts between the bracing legs and the center post are horizontal. (Note - the safe way to open this is to pull each of the three bracing legs outwards.) Tighten the clamp so the bracing legs are firmly set.2. Extend just the upper-most vertical leg pieces on both legs. (Leave the lower two extensions down.)3. Assemble the cross-bar - follow the directions and ensure you have the bars in the correct order AND the two end pieces should have the larger through-holes at the extreme ends.4. Remove the wing nuts and washers from the legs and set them aside.5. Slide the screen onto the cross bar - take your time and avoid catching the fabric on the feeding end of the cross bar - don't get impatient and tear the material. (The material seems strong enough, but just take it easy...)6. (one person can do this easily, but two make it real easy) Place one end of the cross bar on the post on one leg, then repeat with the other end - moving the leg as needed to match the bar length. Make sure both legs are stable and not tilted.7. Fasten the bar to the legs with the washers and wing nuts.8. At each end, fasten the top two velcro straps around the top-most leg sections (if you don't do this now, you may need a small step-ladder later).9. At one end, loosen the next section and extend it (I was cautious and did this in two steps to avoid stretching the screen material. There is a marker line when it is fully extended. Tighten the clamps on both ends fully.10. At each end, fasten the next velcro straps around the middle leg sections.11. At one end, loosen the last section and extend it. There is a marker line when it is fully extended. Tighten the clamps on both ends fully.12. Fasten the remaining velcro straps around the lower leg sections.13. As needed, adjust the legs (and/or velcro straps) to remove any sag or ripples.(Note - I am only using this indoors, so I didn't use the ground anchors or the tie-downs.)Disassembly is similar, but even easier:1. Unfasten all the velcro straps on both ends (all the ones you can easily reach - you can leave the top ones for later).2. Slowly and easily, loosen the bottom leg section clamps and lower the legs, then tighten the clamps. Again - I did this in two steps to avoid excessive stretching.3. Repeat with the middle leg section clamps.4. Unfasten any remaining velcro straps.5. I found it easiest to remove the cross bar and screen at this point, with the lower leg section still extended.6. Remove the wing nuts and washers from the two legs and put them aside.7. Remove the cross bar and screen from the legs.Note - ideally have a very clean floor/rug, or if you have friends helping, try to keep the screen clean while disassembling.8. Slide the screen off the cross bar. Fold it down into a small enough area to fit in the screen zip-lock bag.9. Disassemble the 5 cross bar parts and put them back in the longest bubble-wrap bag. (Note - rubber bands around the ends will make getting them in the bag much easier.)10. Fasten the washers and wing nuts on the legs.11. Loose the last vertical sections of the legs and collapse them fully, then tighten the clamps.12. Loosen the clamp holding the three bracing legs on each support leg and collapse them, then tighten the clamp.13. The two legs now fit in the two smaller bubble-wrap bags.14. The three bubble-wrapped pieces (legs and cross bar) and the screen bag all now fit in the carry bag.So - I set it up in our dining room where the east-facing wall is all glass - clear and very sunny day here at 1PM. I set up the projector with the sunny display behind it and the screen facing the bright daylight.The projected display on the screen was sharp, clear, and plenty bright.Very satisfied - easy to assemble and disassemble - excellent image quality. The materials all seem to be good quality. The metal parts all seem solid and well made. The screen folds and unfolds and doesn't appear to take any creases.Overall - great product - exactly as described and works great.

(Admittedly, the first one that delivered was missing part of one support post and required replacement. Amazon made it easy to send a replacement and fortunately I had time available before I needed it.)This really is a great screen! It's huge - the perfect size, can be setup easily by 1 or 2 people in 5-10 min or less. The support bar across the top and hook-loop along the sides keep the screen taut and, amazingly, NO WRINKLES! I used it inside, so no issue with wind. Outside, you're going to need to secure it for any breeze, at least with the included parts; perhaps more might be required?I used this for a professional video showing at our church. The film hosts were so impressed with it after touring the country at different venues that they asked me if they could possibly buy it from me; I was pleased to.give it to them as a gift, knowing it will get plenty more use. Super pleased, even with the initial quality control issue, quickly resolved.

Ok this thing is huge. Big like Wyoming is big. Nice material. Absolutely works with behind the screen projection. The issue is with the stand. Its flimsy for something so big. Buts thats not the biggest problem. The point where the horizontal bar assembly attaches to the vertical post is aluminum on aluminum with a steel screw cap. Can you guess what happened when a gust of wind pushed on a 150 inch sail? Well it just snapped the threaded rod aluminum part off like twig. Luckily i made a replacement part with a welder temporarily and if that goes i can thread a full size steel rod down the length which wont go anywhere, but seriously guys. That part should have been reinforced. Its a 200$ screen. Also you need to batten it down like a tent. HOWEVER. You dont need to use it fully deployed. Fold it in half and at 75 inches its very manageable for daily use. Picture quality is superb.

I recently used the Towond 100-inch Projector Screen and Stand for a camping trip, and it was a fantastic addition to our outdoor experience. Setting it up was quick and easy. The screen is large enough for a great viewing experience but still lightweight and potable. The screen is made of a wrinkle-free material that ensured a crisp image. The stand held up well, even with a light breeze. It's perfect for camping movie nights.

So easy to put up, one person can do it easily. If you are using it outside you will need to secure it with the ropes included as it is fairly lightweight and will blow in the wind. Easy to wash cloth that does not wrinkle, making it easy for storing.

The size, generally easy assembly of the screen, and the ability to see an image on both sides made the concept a good one. However, the tripod failed to lock at appropriate heights after about 6 uses. Emailed the company, received two canned answers (seemed computer generated). As soon as I asked for a replacement tripod -- no reply. Update - received a reply and a new screen with tripods etc. Too bad the product didn't last long in the first place, but kudos for the final customer service effort.

Really liked it, the fact that it can be projected from behind is very useful. Yes it’s a sail so weighed it down

The screen is unable to stretch enough to get rid of the wrinkles. If the horizontal bar was about 6 in longer then you'd be able to have some stretching and the screen would be better.

me encanto lo portátil y fácil de armar

El tamaño es bueno pero mi espacio donde lo iba a usar era menor.. por lo cual 300" era un exceso para mi cuartito ... Pd. Me llego bien arrugado el producto y en su descripción dice Anti arrugas xd

I HAVE A LARGE PROJECTOR AND THE PICTURE LOOKS AMAZING ON THIS. IT DOES COME CREASED BUT IF YOU PULL IT TIGHT ENOUGH THERE ARE NO CREASES.