Your cart is empty.
Your cart is empty.
Upgrade your Fluke Scopemeter 120 with the Artisan Power Replacement Battery. Specifically designed as a direct replacement for the Fluke 120 series, this high capacity battery pack offers enhanced performance, extended operating time, and improved reliability for your Fluke Scopemeter 120. With its easy installation process, the battery pack seamlessly fits into your device without the need for any modifications. Say goodbye to frequent battery replacements and enjoy longer usage time with our high capacity battery. Crafted with premium quality materials and subjected to rigorous testing, our Fluke Scopemeter 120 replacement battery meets or exceeds OEM specifications, ensuring reliable and consistent performance. Upgrade your Fluke Scopemeter 120 today and experience the power of the Artisan Power Replacement Battery.
Customer
2025-08-24 17:56:06
Bought battery for Fluke123 scopemeter. Fit great and works great
Mike retired USAF
2025-08-15 17:24:59
I have a very old Fluke 123 scope meter that gets lots of use and so far the battery is working well.Make sure to do a full charge up when first installed and it does not hurt to do the battery refresh procedure once.Thanks for a battery product that plugs in without problems.
Russell
2025-08-10 11:49:22
It works but doesn't last long. It was also a lot less expensive.
Ashu
2025-08-05 14:48:22
So after receiving product i just installed it after 60 days and the item and it did not work. It only holds a charge for 5 minutes and takes several hours to indicate it's fully charged. Unfortunately, I cannot return it, so it feels like a complete waste of money.
howg
2025-07-01 10:01:52
I think that I must have not fully seated the plug in the meter on the first try. I did follow the advice here to observe the stock battery plug/pin orientation on first installing the new battery. But after charging for 6 hours, the scopemeter 125 would still only turn on with the stock AC/DC “wall wart†plugged in. I then measured the voltage on the old battery (3.6v) and on this new battery (4.8v), and decided to try again. I put the new battery back in, and (once again) pushed it in as far as it would go with slight pressure. This time the scopemeter worked with battery alone. Yeah!
Jose Nieto
2025-06-30 17:43:42
funciona perfecto
K. D.
2025-06-22 13:13:16
Battery fit fine and works good.
Bigbear77
2025-06-11 11:27:34
Works as advertised as a replacement for the old NiCd battery pack that was in my early generation Fluke 123 Scopemeter. It charged up properly when installed and I now have battery-only operation again, freeing me from having to run the instrument with the charger attached. The reason for the four stars and not five is that the 6-pin connector that plugs into the meter is lacking a polarizing (orientation) tab on the housing. This tab helps to keep the connector from being plugged in upside down since there are no polarizing pins installed in the connector to prevent this. Attached is a screen capture for the Fluke 123 service manual that shows the proper orientation - the row with only two wires goes toward the top of the battery compartment as shown.
Customer
2025-05-17 10:43:08
Bought battery for Fluke123 scopemeter. Fit great and works great
Mike retired USAF
2025-05-09 10:17:01
I have a very old Fluke 123 scope meter that gets lots of use and so far the battery is working well.Make sure to do a full charge up when first installed and it does not hurt to do the battery refresh procedure once.Thanks for a battery product that plugs in without problems.
Russell
2025-04-04 16:20:59
It works but doesn't last long. It was also a lot less expensive.
Ashu
2025-03-31 16:58:38
So after receiving product i just installed it after 60 days and the item and it did not work. It only holds a charge for 5 minutes and takes several hours to indicate it's fully charged. Unfortunately, I cannot return it, so it feels like a complete waste of money.
howg
2025-03-14 10:53:54
I think that I must have not fully seated the plug in the meter on the first try. I did follow the advice here to observe the stock battery plug/pin orientation on first installing the new battery. But after charging for 6 hours, the scopemeter 125 would still only turn on with the stock AC/DC “wall wart†plugged in. I then measured the voltage on the old battery (3.6v) and on this new battery (4.8v), and decided to try again. I put the new battery back in, and (once again) pushed it in as far as it would go with slight pressure. This time the scopemeter worked with battery alone. Yeah!
Jose Nieto
2025-03-03 10:28:06
funciona perfecto
K. D.
2025-02-20 13:57:14
Battery fit fine and works good.
Bigbear77
2025-02-09 12:06:48
Works as advertised as a replacement for the old NiCd battery pack that was in my early generation Fluke 123 Scopemeter. It charged up properly when installed and I now have battery-only operation again, freeing me from having to run the instrument with the charger attached. The reason for the four stars and not five is that the 6-pin connector that plugs into the meter is lacking a polarizing (orientation) tab on the housing. This tab helps to keep the connector from being plugged in upside down since there are no polarizing pins installed in the connector to prevent this. Attached is a screen capture for the Fluke 123 service manual that shows the proper orientation - the row with only two wires goes toward the top of the battery compartment as shown.
Recommended Products
$130.69
$ 60 .99 $60.99