Your cart is empty.
Your cart is empty.Product Description
F80 is a soft and elastic resin. It is available in black and pink, and the prints can remain soft even in the cold winter.
Since soft resin is difficult to print, and the viscosity of this resin is very high, it is not recommended for novices to use it.
Cleaning and Post-curing
- Cleaning tools: Soft brush or Ultrasonic cleaner or 2 in 1Wash Cure Machine
- Cleaning time: 3mins
- Cleaning solvent: 95% Ethanol or IPA
- Post-curing light source: 385-405nm UV(40W)
- Post-curing time: 4-6min
The difference between F80 and F69
Resilience: F80 > F69；
Shore hardness, tear strength, elongation at break: F80＜F69;
F80 prints can remain soft at low temperatures, F69 prints will become hard.
Performance introduction
Mechanical Properties
Shore Hardness: 50-60A
Tensile Strength: 3.8MPa
Tear Strength: 9.75KN/m
Elongation at Break: 159%
Viscosity（25℃）: 2300mpa.s
Elastic Modulus: 1.8MPa
Printing Settings
Layer Height(mm):0.05mm
Bottom exposure time: 35-50s
Normal exposure time: 1.7-10.2s
If you need specific settings, please visit the RESIONE official website
schylar burgess
2025-09-01 15:30:00
The media could not be loaded.
Cammeron
2025-08-18 18:35:22
This resin produces awesome prints. I used an Anycubic Photon M3 Plus with the configuration file from Resiones website. The very first print came out just as good as my dialed in prints using non flexible Elegoo Water washable resins. I did not expect that.The good:The resin is very flexible, retains/returns to it's shape after being flexed, doesn't peel or break apart and picks up even fine details.The bad:It's expensive, more than you realize. Because the prints are rubber a large number of people will likely use this for functional parts which are less likely to be hollow meaning you use more of it on top of it being pricey. Aside from price it smells, and not to a small extent. At first I thought it was just a bit stronger than normal resin however I left home to go to work and came back and it hit me hard, it smells like resin mixed with tire fire. I continued to print with it with my windows open and after about 6 hours of printing noticed my eyes became irritated if I was near the printer for long periods of time (such as while cleaning batches of parts while others printed.) It's also messy. 99% IPA doesn't cut through it much. I found I hand to dunk it in IPA, rub it clean with my hands, then lightly use a toothbrush to clean the "goop" out of nooks and crannies on the parts. After that I can finally cure it.It's a great resin but it requires far more effort, twice the money, and goes half as far. I would not use it unless it was absolutely needed. It's neat, but hardly worth the cost for the novelty.
Robert
2025-08-09 15:20:14
This resin is tricky and temperamental and takes some testing to get a good outcome. But now that I understand its properties and the environment it requires I’ve had a very successful experience and now I’m making usable parts. Maintaining proper viscosity is the key to a successful print. I made an internal heater for my printer to regulate the chamber temperature as well as measuring viscosity and resin temperature before I begin the print. If I do this I’ve had 100% success.I’m using a elegoo Mars pro 2
Sergio Andres Betancur C.
2025-08-06 14:51:49
Great results
Customer
2025-07-20 17:45:26
This resin ripped a hole through my vat and ruined my screen protector. I first used it right after replacing my vat membrane. I got two failed prints in a row where the parts came off the build plate and stuck to the vat. I was running it at the recommend settings on the bottle. On the third attempt I increased it's adhesion to the plate by increase ng the first 5 layers cure time to the maximum recommendee setting to keep it from coming off. Then I decreased the cure time for the rest of the print when it's touch the vat to the minimum recommended setting to make easier to separate from the membrane. Last of all I made sure that the file always had less surface area connected to the vat than the build plate. Then after I did everything I could to get it to work a catastrophe happend. This time it didn't separate from the build plate, it ripped a hole in my vat membrane and got resin all over the screen protector on the printers screen. Luckily I only have to replace the screen protector and the vat membrane and it didn't cure resin to the printer screen itself (I hope).It took about two hours to clean up the mess after which my eyes were burning from the fumes it put in the air, which my normal resins don't do. It's also super thick and sticky and it got everywhere since I could poor all of it through my funnel at once and there were holes in my vat. The bits and pieces of unfinished parts that came out were very flexible as advertised but not stretchy or squishable like rubber. I'm definitely returning this product and staying away from it forever.
GeoQuin4
2025-06-12 21:11:23
I’ve tried the recommended settings, experimented to my hearts desire, and I absolutely cannot get anything to stick to the build plate. All it does is cure too the vat and I have a mess to clean up. I’ve tried everything I can think of and just can’t get it to work. It also creates one hell of a mess. It is so sticky (ironic), and gooey it just seems to track everywhere. I’m just frustrated, and I give up.
Client d'
2025-03-11 14:57:48
Great resin but I was unable to make a successful print on photon mono x after 20 attempts with suggested settings and any other settings. Parts keep sticking to the vat.The only part I was able to print was the calibration model which was only 3 mm highAnd it printed with nice detail. Taller parts just keep stretching the entire piece and it detached from platform or destroys the supports
Customer
2025-02-14 11:39:39
Great stuff, you just need to adjust the settings. Managed to print very elastic parts down to 0.8mm wall thicknesses. Acrylic paint well.
Maciej
2024-12-26 21:05:12
I wanted to try this resin because I'm a prop maker and i needed something to replace leather and this resin does that more than expected, it is less flexible than is advertised though and it's hard to work with at times, the residue is really sticky and the prints do not come easily of the buildplate. The price is also quite high but the quality does match it though, the print quality is very good and even on the most detailed pieces there is no detail lost. I have to figure out a way to paint the resin considering normal paint chips off very easily so overall i would say this resin is truly worth it and does what it promises!
Christian W.
2024-12-02 15:50:15
The media could not be loaded.
Germán S.
2024-11-20 13:21:44
La impresión es lenta y hay que respetar los parámetros que facilita el fabricante. Pero llevo 2 Kg consumidos en una Photon M3 y ni un solo fallo. Un dÃa de éstos me atreveré con piezas mayores en la M3 Max.La flexibilidad, elasticidad y precisión son impresionantes. Hay que prestar bastante atención al lavado, requiere más tiempo de enjuague que otras resinas.
カスタマー
2024-11-16 11:49:41
追記ãã®å¾Œã€è¿…速ãªã”対応ã§å…¨é¡è¿”金ã—ã¦ã„ãŸã ãã¾ã—ãŸã€‚ã‚ã‚ŠãŒã¨ã†ã”ã–ã„ã¾ã™ã€‚ã¾ãŸåˆ©ç”¨ã—ãŸã„ã¨æ€ã„ã¾ã™ã€‚å—ã‘å–り直後ã«é–‹å°ã—ãŸã®ã§ã™ãŒã€å†…容ãŒæ¼ã‚Œã¦ã„ã¾ã—ãŸã€‚急ãŽã®è£½ä½œç‰©ãŒã‚ã‚‹ã®ã§ã€æ´—浄ã—ãªãŒã‚‰ä½¿ç”¨ã—ã¾ã™ãŒã€å¯èƒ½ã§ã‚ã‚Œã°è‰¯å“ã‚’ã„ãŸã ããŸã„ã§ã™ã€‚ã™ã§ã«10本近ã購入ã—ã¦ãŠã‚Šã¾ã™ãŒã€ã“ã†ã„ã£ãŸäº‹ã¯åˆã‚ã¦ã§æ®‹å¿µã§ã™ã€‚
Recommended Products