Rev-A-Shelf 6581 Series Stainless Steel 19-inch Tip-Out Tray with Hinges

Nov 2022 Update: Still no rust. Still works great.Original review: I'm giving this 5 stars right now because I easily installed it, despite not having instructions, and it works well. The soft closing hinges are great. However, since I just got it, I don't know if it will rust. If I see rust in the future, I'll lower my rating.Like I said, mine came without instructions. Fortunately, Youtube is full of instructions. Unfortunately, the YouTube instructions I found were not the most efficient. So, I watched those and then came up with my own plan. I'll share it here for those who might need help.1) BEFORE you remove the drawer face from your cabinet, get inside and trace the cabinet opening onto the back of the drawer face with a pencil... all 4 sides. This will make your life way, way easier.2) Remove the drawer face. I'm not going to tell you how to do that because they're all different and I don't want you blaming me for ruining your drawer.3) If you're going to add a drawer handle, measure and drill the holes for that first, but don't attach the handle yet.4) If you don't have a template (or even if you do), you can use the hinges themselves to mark where the screw holes should go on the left and right sides of your cabinet opening. (Note: The hinges are marked left and right.) Hold the hinge so that the small flat part that is at a right angle to the rest of the hinge faces towards you at the bottom of the hinge. Keeping it in this position, press the tall part of the hinge against the left or right side of the cabinet opening, lined up with the front and bottom of the opening. (See my photos.) The hinge will be wider than the area you're pressing it against, so it will stick out the back. That's fine. Use the holes in the hinges to mark where the screws should go. Then, drill guide holes, but don't screw them on yet! (This is where I differ from the videos.)5) Now, line up your hinges on the back of the drawer face. If you've marked the outline of the cabinet opening, just line up the flat edge of the tall side of the hinge at a right angle along the left or right side and bottom outlines so that the rest of the hinge is on the inside of your outline and the small part is lying flat against the drawer near the bottom of the outline. (Sorry if this description is confusing. I didn't think to take pictures as I was doing this.) Mark your holes using the holes in the small flat part, drill your guide holes, and then go ahead and screw the small flat part of each hinge to the drawer face using the screws with domed heads.6) Arrange the tip out tray between the two hinges so that the bottom is slightly above the bottom outline you drew and the tray is centered between the hinges. Mark your two screw holes, drill guide holes, and screw your tray into place, leaving just enough room between the screws and the tray that you can slide the tray in and out. If you leave them like this, you'll be able to slide the tray out easily for cleaning later on.7) Remove the tray, leaving the screws in place.8) If you're going to add a handle, screw it on now using the holes you drilled earlier.9) Now you're ready to attach the drawer face back onto the cabinet. Line up the long sides of the hinges with the guide holes you made earlier and screw the hinges onto the right and left sides of the cabinet opening using the flat-headed screws. Doing it in this order means that you can use a full-sized screwdriver for this part and don't have to climb into your cabinet to attach your hinges to the back of your drawer face.10) Once both sides are attached, slide the tray back on and test to make sure the drawer opens and closes smoothly.

I’m only giving this a 4 cause it came with no instructions. Thank goodness for YouTube. Nice quality.

This product details to come with hinges and does not. Oak market is not an authorized seller for this manufacture. You will get no support from Rev a Shelf.

No instructions but easy to install

VERRY PLEASED WITH ITEM

Awsome tuned unused drawer front into usable space.

This item has started rusting after o lay a couple months. I would not recommend for any area where there is water

No directions or templates Took all afternoon to line up Disappointed in packaging and no information Thank goodness for YouTube