Your cart is empty.
Your cart is empty.Product Description
Product Features
APPLICATION
This model can be compliant with most standard receiver connector: Futaba, Hitec, Sanwa, GWS etc...
Great for truck, boat, racing car, 450 helicopter and airplane, robot, vehicles & remote control toys
Note
Please keep the servo clean and away from dust, corrosive gas and humid air.
Specifications:
Type: ES08MA
Color: Black
Stall torque: 1.5 kg / cm (4.8V), 1.8 kg / cm (6.0V)
Working current: 200mA
Speed: 0.12 sec / 60 degress at 4.8V; 0.10 sec / 60 degress at 6V
Size: 24mm x 23mm x 11.5mm / 0.94'' x 0.9'' x 0.45''
Line length: 250mm
Weight: 12g
eugenio cuesta
2025-08-30 21:57:53
Excelente producto
chris anderson
2025-08-09 12:38:51
I have used these is some rc builds and regardless of vehicle type they are strong and reliable. I have installed these in a monster truck, shortcut car, a boat and one on a airplane and have had no troubles so far.
Customer
2025-08-04 14:11:51
happy
Andres Caro
2025-07-26 15:40:37
excellent article.... and to fast delivered
Roger
2025-07-18 16:06:08
I bought this to replace 2 servos that were jittering which I had unsucessfully tried to fix (ferrit core, reroute wire, etc). easy to replace and no jitters. I needed to reverse one of the servos and it was a breeze (reverse the 2 motor wires and reverse the 2 OUTSIDE wires going to the pot)
Evan Todd
2025-07-06 15:35:29
These are not EMAX servos as advertised. You can see the difference in the photos by the stickers. Different fonts, colors and horrible placement. Even plugged one in to try it and they are WAY worse than factory servos. Super noisy and hardly any torque to them.
RZR Dad
2025-07-04 15:25:49
Buyer beware, these mention nothing in the add about being an Emax servo yet they have placed a label on the servo calling it an Emax servo. I did not purchase these expecting them to be the real deal, I just needed some cheap servos for a cheap project I have going. What I didn't expect was to receive servos that are branding themselves as an Emax. The logo is incorrect, these are clearly not real Emax servos and are knockoffs. IF you notice the E with the red stretched out block to the left, that is the fake way of labeling them. The real servo also has a trademark symbol in the lower right corner. I have the same authentic Emax servo and these are slightly bigger. Photos are of the knockoff.Anybody claiming in the reviews to be the real deal are being fooled.
Kim Shelton
2025-07-02 15:26:01
Perfect servos for the perfect price. I dont take them under water
Steve
2025-04-25 16:28:11
Great little servo’s for light balsa and foam model RC planes.
Bill Shuttleworth
2025-04-02 11:19:37
These are exactly what I need to finish another truck build they work great.
Trevor Clarke
2025-03-19 17:08:50
After using the plastic-gear 9g version of these motors, I had quite a bit of trouble figuring these out.In the end, it turned out to be mainly my fault. The main issue I had, was trying to figure out how to properly use them. With my previous electronic setup, I found that when I issued movements to the servo, it would work at first, and then it would spin indefinitely (and would refuse to listen to any PWM commands).This confused me for two reasons: 1) I didn't understand why the motor was not listening to the PWM any more and 2) I didn't understand how the servo was continuously spinning in one direction (despite seeming to not be a continuous motor).Turns out the following:What was happening was that my power supply was fairly bad, and thus, when using these beefier servos, the power supply could not keep up. This, I assume was causing the servo to crash, stop reading the PWM signal.I read reviews of other Servos that advertised "continuous 360 rotation when powered off" so that tells me this motor is probably something similar.I also read another comment from someone saying that continuous motors have a tendency to continue doing the last received command.So in my case, I think what was happening was the following:The servo was given a signal to move to a position.The microchip would crash and stop reading the PWM.The microchip loses connection to the PWM and defaults to continue what it was doing before (moving). And thus, the servo doesn't stop spinning.Anywho, once I swapped out the power supply, I didn't have the same problem.I noticed someone else in the reviews mention this spinning behaviour, so hopefully, this is helpful to someone.
Shawn
2025-03-08 14:18:50
I gave 4 stars because these are re-brands. That being said , I cannot tell the difference from the real emax. The work extremely well, no play, and are very quiet. I will buy again
Dmitri H.
2025-02-14 15:57:28
One died after like 5 min of use, rest are okay for now. Using as shift/diff lock servos in trx4, mounts took some sanding to fit, servo horn is a different size then stock, made the plastic ones it comes with work for now, kinda jittery, decent torque and speed, doesn't say it is, but definitely not water proof at all, will report back after some use.
Recommended Products
$13.99
$ 7 .99 $7.99