Your cart is empty.
Your cart is empty.Use the Sonic rafter RW8941 perforated sanding finger pad with the preferred grit sanding sheet to sand the most detailed and small areas. It easily fits into corners and the tightest spaces. No more wrapping sand paper around your fingers, with the finger pad, simply attach it to the sonicrafter, pick the sanding sheet grit, and sand the most detailed and tight spaces with ease. For use on Rockwell Sonic rafter and Shop Series Sonictool models, RK5139K. RK5139K, RK5140K, SS5120.
David M.
2025-08-27 09:40:41
this was very good the quality is great pays to order brand names I recently ordered an off brand and the pads would not stick I should have returned them
M. J. Civello
2025-08-24 13:26:45
Got 15 minutes out of it before failure. The thing has weak rubber between the metal and the hook and loop material to keep the pad in place. At the pointy end, there's not a lot of material there and that's the part moving furthest. So all the force, with not enough material to keep it sticking... yields a bad design. The top third of the thing couldn't handle the sanding of 80 grit on paint on a boat. The friction of the pad on the paint won and the rubber/hook&loop quickly disintegrated leaving the point of the pad to stay in one place the base was moving back and forth. So unless you're doing 220 grit on smooth wood, I would pass on this. Now only the bottom half has the hook and loop so there's no way to sand in a corner making this item wasted $$$ for me along with the other 19 sanding pads I purchased. Worthless!
RM
2025-08-11 14:48:40
i bought two of these to try them out for a stair job im doing(im in the flooring trade, sand and finish) and i was very disappointed because the first one didnt last me half of the stairs (which usually they do, i know heat is a big factor so i carry a vacuum with me when i use them and i go the lowest setting so it doesnt melt the velcro) so i left the other one untouch, but man was i happy when this fit under the fire place rock, never would’ve thought about it, so i baby it and it work great! It save me a night of sore finger for sure
Mark Shepherd
2025-07-26 18:43:42
Good quality
Customer
2025-06-03 10:53:26
I read some of the reviews before purchasing this item but thought I would try it and be careful. Well, I found out that most of the negative reviews were correct about this item. I tried to use this item as carefully as I could and still be able to use the item. I even tried using water and wet or dry sand paper to try to keep it cool. It took no time at all to discover the reviews about the product melting with very little use. I limped along but bottom line is that it does not work as a sanding attachment. If I have to be that careful, as in no pressure and only use it for a couple minutes at a time, then the product has design flaws, in my opinion. It was the perfect tool for what I needed it for but it just didn't hold up to what I call normal sanding. Someone needs to go back to the drawing board.
rockytop1989
2025-05-25 18:55:18
I’ve only used this one time (to sand some cabinets for painting). However, I chose to write an early review based on the reviews I read when contemplating whether to buy this. I read so many people having trouble with melting the accessory or it falling apart. For $6 I couldn’t pass it up nonetheless. I haven’t had any issues, and it fits my Kobalt OMT perfectly. I even purchased some finger sanding pads that fit this accessory perfectly. It works well for tight spaces and around those fancy little crevices in custom cabinets.
DARRELL L WILLIAMS
2025-05-18 13:29:08
I hate to put down anything or anyone but I can't believe that Rockwell put this sanding attachment out in the hands of there long-term fanatic loyal Rockwell followers. I gave them the benefit of a doubt when I received the first sanding accessory and used it about twenty seconds when it had a major meltdown and wouldn't even hold another sanding pad. So I had another sent to me to replace the one that I thought was just a one time bad part but to my amazement it didn't last but a few seconds longer than the first. So what else can I say but I do not recommend this great idea that flopped for anyone to purchase it is the worst part I have that I wanted needed to work. It's just not worth the postage.
makergirl
2025-05-07 10:25:13
Great idea but I had same problem as everyone else: the "Velcro" melts and renders useless. The tip is the weak point but that's the whole reason for this attachment! I'd only use this with a variable-speed multi-tool on its' lowest setting. It's frustrating to buy a tool to save time only to have to work slower than by hand... Great idea - not sure how you could fix. PSA (i.e. 'peal-n-stick') would have the same issue (i.e. would heat up, melt & fall-off). A 'sandwich' with pre-cut pads?
Donald Archer
2025-03-31 16:22:42
Perfect fit for my older Rockwell sonic crafter
Cliente de
2025-03-14 14:53:08
Me sorprendió mucho la calidad de esta pieza para lijar y le quedó perfectamente a una herramienta de la marca Dremel por si se preguntan.
RM
2025-02-19 13:34:51
Was great for what I needed it for. Nothing else could reach the tiny places on my deck that needed sanding. Only 4 stars because like many other mini sanding finger fingers say, it only lasted a few minutes before it was unusable. Do not put any pressure on it and it should last long enough for just the unreachable section you need it for.
Mark H.
2025-01-05 12:20:22
I inherited an Original Rockwell from. my father. The foam/velcro on the sanding head had degraded. This replacement looks a bit different than the original but works perfectly and fits the original sanding pads.
George P
2024-12-20 09:05:44
The surface that is supposed to hold the sanding pads seemed to melt smooth and will no longer adhere to the sanding pads. This happened after 15 min of sanding. It is now completely useless
Recommended Products
$30.21
$ 14 .99 $14.99