Your cart is empty.
Your cart is empty. Safego 50W 3ohm Led Resistors For Turn Signal Light or LED License Plate Lights Fast Hyper Flash Turn Signal Blink Error Code Fix
Specifications:
Power: 50W
Resistance: 3ohm
Number of resistor: 2 pcs
Material: Beautiful golden aluminium housing, Plastic, Wires
Can be used with LED headlight, fog lights...
Standards And Certifications: CE/RoHS Compliant
This 3 Ohm, 50 Watt resistance can be connected solves most LED Headlight error notifications. This will solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. One resistance is required for each turn signal bulb.
Car Usage:
Dome light, Map light, Trunk light, License plate light, Side marker, Backup light, Side Door Courtesy, Luggage Compartment Light, Cargo light, etc
Common Vehicle Usage:
Car, Truck, SUV, Van, Motorcycle, Scooter, Trailer, RV, Boat, Marine, ect
Note:
*The load resistor on the decoder wire will get really hot, please make sure to mount the resistor to metal and don't touch it when the LED light is on.
*If you are not satisfied with our products,please contact us before leaving a negative evaluation,we work together to solve the problem.
Package Included:
2pcs 50W 3ohm Load Resistors + 4pcs Quick Wire Clip
Brian Benedict
2025-08-17 14:44:07
It resist the power
Jeff
2025-08-11 14:31:40
Quick shipping, great price & easy install, test light to verify power wire to turn signal (left White stripe/Blue wire—Right White stripe/green wire ... Black = Ground). Soldered wires instead of using the scotch locks. Installed the LASFIT LED Amber bulbs 💡 & perfect on/off with no Hyper flash or bulb failure advisory’s from the computer. 2 X self tapping screws mount the resistors & your ✅— this was done on a 2018 Chevy Silverado in less than 40 min. Grill & headlight assemblys removed.
Jason
2025-08-04 16:31:34
I installed two of these on my 2010 Dodge Challenger SRT8 after installing LED tail lights. No more “fast blinker†indicator. I did have to replace one of them about a month ago, after I started getting the fast blinker on the right side. All the bulbs and connections seemed good so I switched out the load resistor with the extra ones that came in the pack and everything has been fine.I originally used 3m adhesive to secure them to frame, but when I went to replace the bad resistor. I noticed it was just hanging there. The resistors have holes on the end for screws. I drilled a small hole into metal right behind the taillight and now the resistor is secured.I highly recommend screwing them to something metal due to how hot these get even after a few seconds. Will damage anything plastics.
Cj Crawford
2025-07-18 13:54:41
Bought to fix my hyperplasia after installing leds and it works very well I have had zero issues just took a little work to install but if you have basic wiring knowledge it will work just fine
Customer
2025-07-16 14:06:37
As described.
Quinton
2025-06-05 18:47:33
These are great resistors but the included wire taps are junk.You should do a proper job and make the wire connection in a better way.
Harold
2025-05-27 18:32:54
I used these to stop the hyper flash on my 1984 Honda cycle when upgrading to led blinkers. The warnings about heat had me worried because everything on the bike seems to be surrounded by plastic so I used insulated aluminum faced tape on the plastic near them. I held one in my hand for a couple of minutes while the flasher operated and it did not get hot so I think it is good. I soldered then instead of using the supplied connectors. They worked as advertised. I have not tried one on the tail light that is always on so it could possibly heat up.
Gregory
2025-05-15 16:10:24
definatly remove hiper flash. wires are wrapped in a fabric braid style. made it kind of hard to strip. wires are definatly long enough to support a permanent mount. holes for mounting are very close to the body making it quite dificult to use a standard sized self tapping screw to mount. all in all great product. does not get very hot but recommend mounting to a flat metal surface.
BORDALO Jose
2025-04-05 15:45:54
Gostei.
Techie
2025-03-11 14:15:54
Used these for a Motorcycle turn signal, and only two required for the four flahers converted to LED. Easy to install, I soldered mine and heatshrunk the joints. I had no metal to use as a heatsink so I put them back to back to each other. They don't get warm (motorcycle current is low) but just in case. They came fast and seem like good quality.
Rick Burton
2025-01-19 16:08:57
Easy to install
markus hörmandinger
2025-01-03 17:58:27
Die Erwartungen wurden voll u ganz erfüllt! Funktioniert einwandfrei u wurde rasch geliefert. Werde wieder bestellen wen ich etwas benötige! MfG
Andrea
2024-12-12 16:32:54
Buon prodotto come da descrizione
Recommended Products
$45.00
$ 23 .99 $23.99
$15.49
$ 5 .99 $5.99