Your cart is empty.
Your cart is empty.
UNVERT Metal - Zinc Self-Drilling Drywall / Anchors are self-drilling drywall anchors and provide excellent holding value and much greater capacity than screws alone. This anchor cuts threads into drywall, greatly increasing the bearing surface and strength of the fastening. Strong Zip Tip does not sheer off when self-drilling.
Kit Contents:
10 E-Z Ancor - Zinc Toggle Anchors, & 10 Phillips Screws (#8 x 2-1/8'') - Total of 20 Pieces.
It comes in a resealable plastic holder container, that even you don't need all of them now, you should be able to store them, it shouldn't get lost.
Package Dimensions: 4.5 X 3 X 1.2
SIMPLE INSTRUCTIONS:
E-Z Drywall Anchors are easy to install - all you have to do is zip-it into the pilot hole of the drywall.
BUY WITH CONFIDENCE
We back all of our Anchors with the best warranties in the industry and they are guaranteed to exceed your expectations. If for ANY reason you don't agree you can contact us at any time for a replacement or refund.
ABOUT US
UNVERT is known for the best brand of Anchors in the construction industry for decades, with its strong hard material, it works magickly and you can store the extra in our well-made containers, or reuse for many times because of its world known high quality.
Awriterreads
2025-07-27 15:52:54
My young hound mix ripped the curtain rod from my third bedroom. I tried many other types of toggle bolts but none worked. These did!
Brandon Jones
2025-06-20 10:50:45
I ve been a handyman for years. If you need an anchor that holds a lot of weight and is really quick to install, just one Phillips bit does the job, this is the last anchor you will buy!!!
Mark Edel
2025-04-05 14:33:36
These are not for every application, as they make very large holes and don't always end up perfectly flush with the wall. However, they are a lifesaver when you need to detach and reattach the screw, such as when you're hanging something large that you can't see or reach around to place the anchor while it's attached.
Selena
2025-02-21 11:07:01
The anchors themselves are great; sturdy and drill into the wall easily. However, the screws that come with itare sometimes too thin. As in i could push the screw in and pull it out with my bare fingers because the treads dont catch.So far nothings fallen down yet...
GEORGE JOHNSON
2025-01-15 11:40:17
Once you get the tube in the wall you have to put the screw in and it pops out the anchor. Then the screw has to go the a hole in the anchor and is supposed to start threading thru the hole. It would have worked if the hole was threaded but it looks like it was just punched. As a result the the screw wont threads in the punched hole and the anchor will not tighten against the wall board. Now I have a big mess with damaged plaster and no anchor..This is 90% of a good product but they cheaped out on the most important step. DO NOT BUY.
Banmo
2024-12-13 15:34:24
These work very well, I have large antique clocks that are valuable; if I can’t use a stud, these in Sheetrock work very well
Mute
2024-12-10 17:45:20
I love these. Very easy to install, ultra strong, and nearly as easy to remove should the need arise. Yes, they are removable!There's a simple trick that requires a thin pick or philips screwdriver: remove the screw; then loosen (but don't remove) the anchor from the wall and rotate it so the words "EZ anchor" are at 3 o'clock; then take your thin pick/screwdriver and slide it into the central screw hole, you'll want to slide the tool against the bottom edge of the screw hole while angling the tool upwards; you'll feel a bit of resistance when the tip of your tool contacts the toggle, so just push a bit harder, the toggle will tip over and then you'll be able to fully remove the anchor.There is a YouTube video that illustrates this process very well that I can't link, just search ez anchor removal and you'll find it.I highly recommend these for holding very heavy items when a stud or ceiling joist isn't available.
A. Rucker
2024-11-18 12:58:04
Installed four of these and initially thought all four had failed. Thought I had got the toggle snug and the 'body' was pulling out of the drywall.Submitted a return and was trying to remove the body and it would only come out about a half inch.Put the screws back in and kept on going after I felt resistance. Finally got snug.There are NO instructions with the package and what is on the product listing wasn't clear.Will let the refund expire.
Recommended Products
