Your cart is empty.
Your cart is empty.Product Description
Red/Green LED Traffic Light
The TL Model Lights are our standard LED Industrial Traffic Lights. The sturdy aluminum housing gives this LED traffic light durability in harsh weather environments. The TL Model Lights are suited for use in truck dock bays, fork lift intersections, and roads & parking lots. It has bright LED's to ensure maximum visibility.
Ready to Mount & Use Out of the Box
Just mount with two mounting brackets with bolts included, plug it in and you are up & running. No Assembly Required to Save you Time & Money!
Signaworks - The Industrial Traffic Light
Signaworks continues to be the leader in Industrial Signal Lights since we began over 25 years ago. We continue to create innovative designs for industrial signal and traffic solutions.
Where to Use - Plant Floor, Weigh Station, Warehouse or Traffic Control
This is a great communication tool for signaling fork life drivers, trucks, or any traffic control required. The LED Traffic Light is easy to mount and is Highly Visible for any Industrial Plant Floor application for Signaling indoor or outdoor at long distances.
Jim
2025-09-03 18:06:52
The media could not be loaded.
Joe
2025-08-11 17:48:25
Verify voltage first. Installed outside USPS loading dock. Well made, LED and super bright.
Lisa Triplett
2025-08-03 13:22:26
Product is of good quality, wiring it was a little difficult.
Customer
2025-07-16 14:49:53
Picture shows a cable from the bottom. However, you have to find your own cable to wire and power it. Absolutely pointless!! Very unhappy
Cynthia
2025-07-11 18:20:08
I have a contractor hanging this in my office and they are asking where the wire is for the power source for it to light up? The photo indicates from the bottom of the machine that something should be connected in there but there is nothing in the box other than the light and mounting brakets
Doug Holcomb
2025-06-21 19:09:44
It gives the appearance that it has wires coming out of it to hook up to something, but it is not. Trying to figure out how to send it back.
mary pierce
2025-06-12 10:12:54
I hope it still works my daughter brought it into the house and sent a photo to me there is a huge hole in the box
Skredberry
2025-05-30 11:03:05
The mounting pieces have the machined holes a bit off. Not a big deal, but put flush with the box, the screw holes to the box are 1.5mm off which would increase when a screw is in the bracket to the wall. Better to put a slide hole for varying screw head clearance. Will open it up on my drill press.I had this on my wishlist for quite some time. I think this is a newer model as I’d also purchased a computer controller. Lights are a constant on so I’m hoping the controller will randomize if the knobs are left in the on position.It has a little dent in the back from shipping, but will be covered by the brackets to mount so I’m not overly concerned.I’d just suggest slider holes for the screws that attach the bracket to the unit. I’ll just add 4 rubber washers and paint the screws because I like the powdercoat.
Jim
2025-05-09 20:56:58
The media could not be loaded.
Joe
2025-04-05 10:56:59
Verify voltage first. Installed outside USPS loading dock. Well made, LED and super bright.
Lisa Triplett
2025-03-26 17:40:36
Product is of good quality, wiring it was a little difficult.
Customer
2025-03-13 16:15:20
Picture shows a cable from the bottom. However, you have to find your own cable to wire and power it. Absolutely pointless!! Very unhappy
Cynthia
2025-03-05 15:29:22
I have a contractor hanging this in my office and they are asking where the wire is for the power source for it to light up? The photo indicates from the bottom of the machine that something should be connected in there but there is nothing in the box other than the light and mounting brakets
Doug Holcomb
2025-01-07 09:16:04
It gives the appearance that it has wires coming out of it to hook up to something, but it is not. Trying to figure out how to send it back.
mary pierce
2025-01-06 18:03:46
I hope it still works my daughter brought it into the house and sent a photo to me there is a huge hole in the box
Skredberry
2025-01-05 11:33:15
The mounting pieces have the machined holes a bit off. Not a big deal, but put flush with the box, the screw holes to the box are 1.5mm off which would increase when a screw is in the bracket to the wall. Better to put a slide hole for varying screw head clearance. Will open it up on my drill press.I had this on my wishlist for quite some time. I think this is a newer model as I’d also purchased a computer controller. Lights are a constant on so I’m hoping the controller will randomize if the knobs are left in the on position.It has a little dent in the back from shipping, but will be covered by the brackets to mount so I’m not overly concerned.I’d just suggest slider holes for the screws that attach the bracket to the unit. I’ll just add 4 rubber washers and paint the screws because I like the powdercoat.
Recommended Products