Your cart is empty.
Your cart is empty.Product Description
Debra
2025-08-26 15:28:44
Easy to use! Takes up less space in the freezer than a standard tray. Our freezer is usually FULL so these individual ice balls were easy to slip in here and there. A quick rinse under cold water and they pop right out!
Customer
2025-08-20 13:46:59
These molds are easy to use. They require a little time getting the ice out of the mold, but it produces round ice after you've worked it out of the two piece mold. They don't leak unless you overfill them and then they just push their caps off. Overall a good product.
Retired LEO
2025-08-13 15:38:09
I already own an all-silicone ice ball tray, but wanted individuals to fit in the door shelf , so I bought this 4-pack in black.My existing mold makes ice balls that I measured at 2.5 inches. The ice balls from this FOSOE set measure 2.25 inches. Here are my Pro's and Con's after some testing.PROs: Individuals are easier for me to fit into the freezer due to space, the smaller ice balls (2.25 inches) fit more of my bar glasses, they are easier to fill than my older mold, and the ice ball is solid when removed for a cocktail.CONs: The plastic lid seems thin, but I figured out some things noted in my "TIPs" section. The clear plastic lid fits to the silicone base through friction instead of being threaded like I had assumed. The rubber cap for the fill spout DOES prevent leakage during normal handling. I wouldn't label this as "Easy Release" because you have to peel the edge of the base away from the ice and push it out from the bottom.TIPs (VERY IMPORTANT STUFF):1. WATER EXPANDS AS IT FREEZES !!!2. When I tested the mold with the rubber cap in place, the pressure of the expanding ice seeped out between the plastic top and rubber base - causing a messy situation. To avoid this, I left the rubber cap OFF and let the ice expand upward. Once frozen, I replaced the rubber cap to prevent the ice from absorbing any food odors.3. For those who (like me originally) found the ice ball hard to extract, run the frozen unit under water to help the release. I didn't want to melt too much ice, so I just set it all on the bar while I gathered my other things (booze, glass, cocktail ingredients, etc). By the time I was ready for ice, it had melted enough to slip out of the mold. OR, if you're warm-blooded, just hold it in your hands for a little while... it'll melt a little, loosen up, and release easier.4. IF you let the molds warm up a little (running water, room temps, or hands), you can separate the halves easier and not feel like it's going to shatter or crack.
Robert Smith
2025-08-08 10:11:20
They work great!Be sure not to overfill.
Doyle Brigman, Jr.
2025-07-28 11:43:02
Ok for the money I suppose. But the ice ball is never easy to extract. Would suggest you purchase something better.
D. Wartelsky
2025-06-09 12:40:39
If you like big balls, for your drinks, you’ll want to get your hands on these. Even my wife couldn’t believe the size of these babies and couldn’t wait to get her hands on them for her drink. She asked if she could holdum,and said, “ not only are they big ,they’re pretty smooth tooâ€!Then she asked if those big balls were tough to get out? I replied, no, just run them under warm water and they pop right out!So is this kit easy to use? You bet! Just assemble the two halves and fill using the small funnel that’s provided and place in freezer. Soon you’ll be freezing your balls off, for your drinks!Good product, would recommend.
Steven
2025-05-27 21:58:23
I'm very happy with product. Are the ice balls perfect? No.If you want them to look perfect, you’ll need to do a little scraping.Some of the negative reviews I’ve read about not being able to get the ice ball out of the mold and them cracking and breaking, does happen. Only if you pull the frozen molds straight out of the freezer and try using them without letting them set on your counter or in the sink for a few minutes to acclimate (thaw a little bit).If you don’t let them acclimate, the ice ball will not release from the mold and will crack and sometime break when used in a drink. If you’re in a hurry and don’t have time, just run the molds under a cold stream of tap water and they will release just fine. You may get a few more cracks in your ice ball doing it this way, but it works.
Customer
2025-05-25 18:44:36
Purchased these to make fun ice cubes for the holidays and they were perfect. They were easy to fill and even comes with a little funnel to do so. It was a little difficult to remove the ice but overall I would recommend these!
BillyLH
2025-04-12 10:30:53
Excelente el molde y de buena calidad, los hielos salen perfectos
Dave
2025-04-03 12:04:59
These are bigger and excellent for keeping water cool in the heat of summer and adding the extra coldness to a jug of water.
Sulaiman
2025-03-01 17:37:58
اشتريت اكثر من نوع من امازون وهذا اÙضلهم. اهم شي تعبئته سلسلة وما يهرب مويه واقدر اÙÙƒ الثلج بسهولة. ممتاز بس مشكلته غالي شوي على عدد الØبات.
Sara
2024-12-17 20:39:42
My hubby really likes these to make his old fashioned drinks
Marina lizeth RodrÃguez Navarro
2024-11-28 16:40:13
Muy padres para el whisky, traen su embudo pequeño para rellenar.
Recommended Products