Your cart is empty.
Your cart is empty.XRC Rock Guards are manufactured from 3/16" cold roll steel and hand crafted to insure a perfect fit every time. The rocker guard is finished in a black powder coat and can be used with rear corner guards. They fit with or without factory flares.
A.Rose
2025-09-04 14:18:53
These rock sliders are great. Super easy to install by your self and they look great and are real sturdy. For this price you cant go wrong. The only down fall was the package it was shipped in was all messed up. One of my rock sliders tabs that goes into the body mount was bent. i just bent it back by using a press, it worked fine. I still gave the product five stars because this could have happened due to the shipping.
Robert Ian Toms
2025-08-30 12:39:45
Easy install and very rugged. Lots of compliments ☺
Ric
2025-08-28 17:35:35
Good heavy duty metal, nice power coat finish, be aware you have to remove the body bolts and jack the body off the frame an inch or two to slide the bottom mount between the body and frame, two person job
Eric Camera
2025-08-12 13:41:34
This i the second set of these that I have purchased and installed myself. Love them. They look great, have great protection and the step comes in handy on the trail. A little tip, I used a sharp utility knife to cut down the 3/16" on the body mounts. Rotary tools have a tendency to melt the rubber. Also, these fit perfectly with my Rugged Ridge Hurricane Fender Flares on my 98 TJ Sahara.
Ranger Gary
2025-07-17 11:03:30
These are solid, and the installation is pretty straightforward, although it would be nice if they specified where the body mounts are--took me a while to realize that the "front" mount is underneath the radiator rather than on the frame rails like the other 5 (3 fat ones under either door; 2 flat ones just inboard of the frame, one forward of the gas tank and one right on the rear bumper area). Mine arrived well packaged, although somehow one had a roughly 2 inch elliptical dimple, 1/4" deep in the tube. But these are meant to be beat up, so I just took it as a bit of premature proof of serious jeeping... It is also a bit of a pain on my 2006 as the aft-most hole goes through where there are two layers of sheet metal and you have to use a 1" hole saw from the interior to enable room to tighten the nut properly. Managed it without having to remove seats but you can do a neater job if you do. Bolts are nice quality stainless steel--although they really should be blackened rather than silver to match the finish. Shiny silver just looks out of place on jeeps in my opinion. Welds were neat and workmanlike; tubes are sturdy but not quite as thick as I'd like. Powder coat is evenly applied. For the money, I think these are a pretty good deal.
Jimmy Hunley
2025-07-09 10:50:42
Worked great on my 99 TJ. Toughest part was cutting down the rubber body mounts to make the sliders fit. Installation took 4ish hours - alone. Seems like a great product.
jimmy
2025-07-01 14:42:29
The product was well packaged. It fit perfectly and the shipping was fast .
Josiah Nebeker
2025-05-19 15:35:11
These look cool but that's about it. They don't fit flush to the side of your jeep, so be aware of that before buying. For the price they are hard to beat, but I would save and get Warn sliders or another top end brand. The welds from the tube to the slider itself are pretty bad looking, so if you are picky like I am these are not for you.
F
2025-04-23 11:55:52
Looks good on my tj and pretty well built sliders. Paint seems pretty sturdy and should last long, time will tell. I installed it myself, very easy to follow instructions.
Customer
2025-03-29 16:41:34
Very well made heavyweight rock slides looks fantastic
martin
2025-03-16 10:33:45
Je le recommande et livraison a ete rapideSatisfait
Chris
2025-01-21 16:27:56
The product it self seems well build and solid. However, they did not take into account that the rear hole that needs to be drilled goes the a section of the tub that is 2 layers thick. The supplied bolts are not long enough for this to reach because of this...and of course you will not realize this till after you have drilled a hole threw your Jeep LOL. Also, you have to remove all of your body mounts to install.....so if you have any body mount torque box rust/rot I would not recommend (if you spin any of the captured nuts.. your in for a huge repair to fix).
JRM
2025-01-09 18:07:20
Look amazing fit perfect and extremely well built
Recommended Products
