Your cart is empty.
Your cart is empty.Product Description
DKS
2025-08-31 13:57:33
A little spendy for what they are, but they do work great. Bits don’t fall out but are easily inserted or removed. Much nicer than digging around in your pocket trying to locate a different driver bit.
Paul A. Stoner
2025-08-28 16:55:14
I am a handyman and woodworker. I put one on each of my Dewalt impact drivers, making certain not to cover the motor cooling air vents. Clean drill surface with alcohol 1st then stick one on. I put one on top and one on the side, giving me 6 bits to carry with me. An example would be t25 torx, #2 square drive, #2 phillips. Maybe on the side a 1/4 & 5/16 nut driver also a drill bit of whatever I might need for the job. I had these stuck on my two drills for est 2 years now. Still hold bits well. Fantastic product.
WJC3
2025-07-19 10:00:36
I use these on my DeWalt cordless tools. I remove the dewalt logo, clean off any residue, then place these in the spot. They fit perfectly.I have have one bit in the chuck and 3 on standby.Longer bits can interfere with the drill clutch.The adhesive doesn't seem to work well if the tool gets warm/hot.The tool can be bulky/unwieldy if there are too many long bits inserted.Bit holders are holding up well. None are stretched or split after almost a year for home owner DIY projects.
Cann
2025-07-08 10:29:22
I've been using it for over 2 years, Over time the silicone gets a bit loose. But no tape can fix. Easy to use. Great value for money
T. Caperton
2025-06-30 14:38:15
These bit holders are one of the handiest things I've found for the projects I work on. They sure save lots of time with having to search around for the additional bits I need. The bit holders have great adhesion and stay secure on my drills even when I'm moving/banging the drills around when working on my projects. I primarily use only three type of drill bits on most all my projects, and I can store all three in these holders. I highly recommend these.
Logan
2025-06-14 17:05:28
They work fairly well. Could be slightly longer or include a small stopper to accommodate both a nut driver or long bit and a short bit without the bit getting knocked out. Bought more to save time on the job but now I've had to return it twice because they sent me the same wrong pack twice. Not exactly a time saver anymore, would rather get extra of the cheaper generic ones to avoid the hassle.
Charles Starratt
2025-06-09 11:11:12
Okay, Here is my review. Ordered them based upon the product description and "ease" of application to hold those pesky bits that you have to fish around for when you need them. Product is as described and pliable. Here is the catch though, and something I did not find in the product description. The "3M" tape adhesion covers (The red patch over the sticky) are EXTREMELY adhered to the sticky part. I fiddled with it for about 3 minutes, trying to peel back the protective layer. (Frustration set in and as usual, my thoughts turned to other means of adhering them to my drills) It dawned on me that an application of direct heat might release the protective layer and allow me to stick them to my drills. I recommend a HAIR DRYER on high heat and not a HEAT GUN, with heat applied to the red seal (protective layer) for a few minutes, maybe less, and the protective seal will, with effort, concentration and determination, peel away to reveal the glue adhesive. (You will need to clean oil, dirt and debris from whatever electric driven tool you are applying these to before starting the heat release procedure) Once the red seal comes free you should then immediately apply these holders to the location on your hand tool and PRESS FIRMLY and EVENLY to avoid air pockets. I will see how long they will actually remain adhered to the tools as I am a casual user of the hand tools.I would have given more stars had there been mounting instructions explaining what I just explained to you, they are pliable enough to push bits and such into them and hold them securely. Do not feel obtrusive and do not seem to cause any issues with handling and operation in the position I placed them in, you may need to, and I highly suggest, you pre fit them before adhering to insure they do not get in the way of your hands. they are a bit pricey for what you are getting, but if they help you keep bits conveniently closer than the work bench, tool box or having to go buy more because you cannot find the one you need, then it was worth the cost.
TIM
2025-05-07 12:49:53
I used a heat gun to warm tools and bit holder adhesive before applying. Seems to be holding well so far. Holds bits securely.
Robert
2025-03-04 16:58:55
Great product, fits perfectly, for me works better to stick it to the battery as sometimes I work in tight spaces and that clearance makes the difference. Don't know how stretchy they will be with the time. For now bits holders fit perfectly nice and tight but if you hold just the little drill bits they are just on the limit to be too loose.
RCM
2025-02-23 15:49:23
Very pleased with this product. Adhesive backing proved to be effective. Can recommend.
Deborah Pembleton
2025-01-20 20:45:11
Seems like a great idea but my Son did not like it as he says it can hold heat in the drill so it may not be such a great idea. Also note that it cost me $6.03 to return so be sure you want this product before buying.
Rich
2025-01-14 10:25:57
I’m onto my second pack now after adding more power tools to my collection. The only thing I would say is that they do go a bit slack after a few months but I solved that by putting a bit of superglue just inside it and letting it cure before adding the bit again.
John Rennison
2024-12-12 10:14:42
Amazing adhesive. Holds tight to what ever it is applied to. Hold bits in place well.
Recommended Products