Your cart is empty.
Your cart is empty. This is the strongest model for Nema 23 stepper motor, it with 1.8 deg. step angle (200 steps/revolution).
Each phase draws 4.2A, allowing for a holding torque of 3.0Nm(425oz.in).
Electrical Specification:
* Manufacturer Part Number: 23HS45-4204S
* Motor Type: Bipolar Stepper
* Step Angle: 1.8 deg.
* Holding Torque: 3.0Nm(425oz.in)
* Rated Current/phase: 4.2A
* Phase Resistance: 0.9ohms
* Inductance: 3.8mH+/-20%(1KHz)
Physical Specification:
* Frame Size: 57 x 57mm
* Body Length: 113mm
* Shaft Diameter: 10mm
* Shaft Length: 24mm
* D-cut Length: 20mm
* Number of Leads: 4
* Lead Length: 400mm
* Weight: 1.8kg
Connection:
Black(A+), Green(A-), Red(B+), Blue(B-)
Warning:
Make sure the motor connect to a constant current or chopper drive controller before you test motor.
Connecting the motor directly to a power supply will destroy the motor.
Scott Moore
2025-08-28 14:37:31
used these for a rail system and an arduino build that required a good 50lbs of lift across two motors. These don't disappoint. They can heat up, so I set the stay current to 50% and they still hold steady but stay cool. Good motor.
Distinguished Rifleman
2025-08-25 12:36:01
Wanted to build an electronic turning target frame that runs off a Bullseye Match app on my iPhone/ iPad for practice for Bullseye/ Precision Pistol Matches. This motor provides the rotation. Works ok. Was hoping it would be enough to turn a 6# rotating assembly 90° in around 1 second. it is ok, not ideal. Not like I’d hoped anyway, but then it wasn’t manufactured with my application in mind. The current setup up is direct drive. I may machine myself some pulleys or sprockets and use some tearing or a transmission. Would buy again but I have no idea how they’d work for their intended use in cnc applications I’d rate it at 4 stars but it seems unfair given my “misuse†of the product.
Joel Janssen
2025-08-11 14:14:43
This stepper motor performs very well for my application and exceeded my expectations.I'm using these in a milling cnc I'm building to drive the axis ball screws and have been able to achieve speeds in excess of 2200rpm which with a 5mm pitch screw, translates into 11,000mm/min or over 400IPM. Mass moved during these tests was 60lbs. Granted the torque at this speed is next to nothing for the given voltage but at least is an indicator of where the limitations are. Some details of the setup tested are listed below.Motor driver : M542T (4:1 Microstepping)Power supply: 48V/5A (set to 49.5v) Meanwell NDR seriesBall Screw: unbranded - 1605, 700mm Length, BK mount supports, split clamping coupler.Ways: NSK 35mm Linear guidesRamp profile: trapezoidal curve at 600 mm/sec^2While I haven't tested it but I believe the voltage limit for this motor calculates out to around 60v so one may be able to squeeze out a few hundred more rpm.Other comments:1. Due to the large shaft size, the cheaper non-helical cut couplers are bulky and not balanced well.2. Individual wire leads - most lower cost stepper motors are like this but I'd prefer them as a cable or even better, a fixed circular connector receptacle like a standard M12 connector.
B. Edgar
2025-07-20 11:09:52
The media could not be loaded.
Customer
2025-06-30 16:54:56
Nice motor for the money. Ezcnc builds professional cnc machines and primarily uses high end motors such as Oriental motor but from time to time we use these on "Z" axis. They have held up well. Construction and finish is nice. Wires are a bit on the low end and they don't hold up to heavy cycling. Rotor inertia is hign but expected on a low cost motor. I recommend them for light loads where torque doesn't go past 50%of rated. They fail fast when pushed. For higher applications, stick with the high end motors. For hobby stuff, these are great starter units.. only drawback is they are very rough even at high pulse rates with anti resonance drives.
Benjamin Pelletier
2025-06-28 17:46:37
For those confused, the seller-recommended driver (https://www.amazon.com/gp/product/B074TBMC7N) definitely works, even when powered by a 48V supply. Although V=IR implies that 48V should exceed the rated 4.2A at this motor's 0.9 Ohm impedance, the driver regulates the output so it's fine to use a driver like that even though the driver's power supply is a higher voltage than could be tolerated by the motor when connected directly.
Hot dog
2025-06-22 14:47:11
Attached to auger
D. Irving
2025-04-16 13:29:41
seems to run great, dosen't get very warm.
Truong R.
2025-04-12 18:02:06
je souhaite meme en acheté d'autre mais le prix a flambé , acheté a 35 euros il y a 2 mois :((((
Jesus Diaz
2025-04-11 16:59:44
Es un motor que creo que no fue ideado para impresoras 3D es grande, potente y el eje de ataque es de 10mm, encontré después de muchos intentos un acople de 10x10mm. lo estoy usando para mover un eje de 1600mm de largo con una pieza que debe pesar algunos 15kg. va como un tiro.
Lindsay O
2025-03-07 10:44:51
fitted well works fine good buy
simone
2024-12-05 13:57:18
Imballato alla perfezione funziona benissimo. Molto soddisfatto
Pynaert M.
2024-11-28 17:19:25
100% juist !!!! Vriendelijke groeten Marnik.
Recommended Products
$74.95
$ 34 .99 $34.99