Your cart is empty.
Your cart is empty.This Sunex tool is used for removing steering wheels and features: Cap screw sizes 6/16" (24 x 3" long), 3/8" (16nc x 3" long) and 5/16" (18nc x 3-1/2" long), a specialized puller set for steering wheel, pulley and flywheel puller. It works on most GM, Ford and Chrysler cars. It can also be used as a two or three way puller to remove pulleys and flywheel from small engines an snowmobiles. Made with the quality and durability to last.
Orval W. Stuckemeyer
2025-07-26 14:55:47
Worked perfectly to remove the steering wheel from a 2002 Mustang GT. Happy with the price.
Theodore
2025-07-22 12:05:05
It did the job and I am sure will again when needed. There are not many times when I need to remove a steering wheel but there is no other way than with a steering wheel puller. Lots of combinations of nuts to fit different vehicles so should suffice for any shade tree mechanic who needs to remove a steering wheel.
SP
2025-07-12 13:21:33
Wasn't wide enough for use on Honda steering wheel.
john p.
2025-06-16 15:28:29
Well below anyone's standards. A wheel puller that says it's compatible with all older GM products but doesn't come with the bolts needed is false and misleading to say the least. Going back and getting a refund, I hope!
Anthony F. De Leo
2025-04-12 20:37:42
I purchased this to pull flywheels on Tecumseh one cylinder lawn mower engines. They have 3 holes in a 1 1/2 inch diameter pattern around the center, so 2 hole pullers would not work. I just received it today, ran (well, at my age, walked fast) out to my shop to pull a flywheel. The bolts with it were too big, so I grabbed 3 each 1/4 x 2 inch NC hex bolts with 1/4 over 3/8 inch HD washers. I tapped the 3 holes in the flywheel for the bolts, threaded them until they bottomed out, then started turning the bib bolt in the puller.I heard a pop, being a bit cynical, I was sure something broke. It was nothing more that the flywheel coming loose. Just way too easy! This is far less expensive than the special Tecumseh puller and can be used for many other things.Great tool!
Scott Moore
2025-03-29 18:19:29
I knew it was cheap and a one time use item. So it didn't bother me too much when it bent removing my Mazda steering wheel. If you are not popping steering wheels in and out, then this is good for a single use. It bent the metal push rod trying to get out my Mx-5 steering wheel.
Thomas Hall
2025-02-10 15:25:09
Compared to a similar , nearly identicalLooking product that was thinner ...weaker, and bent at first use ...This one has the beef where it's needed. Center section and arms.Looking forward to using it .
Rhombus
2025-01-21 11:19:30
I am giving this a four star review as it works just fine as steering wheel puller, but for reference, if you are buying this to attempt to remove the front crank gear off a 90-05 Mazda Miata, it will not work without some seriously long bolts from the hardware store and dropping the sway bar and possibly the radiator.
Darren Vars
2025-01-06 11:12:23
Title says it all.First use, one hand with very little effort and it cracked right away.I'm not sure what you could remove with something this flimsy.Now I have to buy or rent another and my project is on hold yet again.Less than not impressed!No negative stars available or it would get the max.Definite do not buy!!!
Recommended Products
$26.99
$ 12 .99 $12.99
$32.29
$ 14 .99 $14.99
$24.99
$ 10 .99 $10.99