Your cart is empty.
Your cart is empty.Fullfill your need for Speed with the Super Summit slide by Swing-N-Slide. This Green, three-piece plastic features a comfortable scoop design with wide handrails that is fast and easy to assemble. The Summit slide easily attaches to any 5 foot swing set deck Height and can support up to 250 pounds. Constructed of durable thermoformed plastic. The slide is proudly made in the USA with a lifetime against cracks and breaks. Upgrade your wooden playset today!
David Vaughan
2025-07-05 12:31:21
This solid is a wonderful product! It lives up to my expectations! I “THANKFULLY†used the recommendation from another review to purchase longer bolts. I was able to insert the longer bolts leaving them slightly loose until all bolts were installed. Then I tightened them all, creating a much easier assembly. If you use the bolts that came with the product, it is extremely hard to align the holes and secure them because they are too short.Once the slide was assembled and installed it is perfect! I tested the slide before putting the kiddos on it and I weigh “slightly†over 200 lbs. I am very confident that it is sturdy and safe.
Jess
2025-06-20 12:21:49
Assembling this slide took a bit more thought and effort than I expected. It seemed like the brackets did not quite fit right at first. I found that using something (a screwdriver) to align one of the center holes while I installed the side bolts helped. I then had to use my impact driver to get the center bolt/nut started. Once the side bolts/nuts and center bolt/nut were started, it pulled the rest of the holes into alignment making the remaining bolts/nuts easier to install. Once assembled, the slide is very sturdy and met my expectations.
JG
2025-04-27 15:53:42
7 days after purchase, it had still not shipped (by Amazon) and had to talk with a Amazon rep who was able to escalate the shipping for the next day, slide arrived 2 days later as promised by the rep. Assembly is straight forward, matching "flat" slide section to a "grooved" slide section secured with 2 metal identical metal plates at each slide "joint" - the problem is all 4 metal plate (2 per slide joint) are exactly the same, but the curvature of the 2 joining sections of the slide are not exactly the same, thus it is very [very] difficult to put together. Best option was to get the supplied bolt through the 2 opposite lower/outer holes first, which was a challenge having to literally twist and slightly bend the metal plates to line up with the molded holes in each slide section. The install a 3rd bolt in the very center hole...this took using a "C" clamp to force the 2 metal plates together enough so the bolt was through the holes enough to start the nut. Be aware, the holes on each slide section to NOT line up properly and I had to fight with the angle of the bolt to get through both holes. Plus dealing with the slope/angle of the slide made all this even harder. This design obviously looked ok on a CAD or whatever software was used for the design, but the reality is the actual fabrication is not accurate concerning the size/shape of the metal plates and thus how they line up with the misplaced holes in the 2 sections of the slide being joined together. Yes, we were able to make it work through about an hour of frustrating assembly that required 2 adults and numerous extra tools to force things to line up. Note: the screws to mount the slide to a wooden deck, or similar installation, are NOT included and basic wood screws will easily pull through the plastic lip at the top of the slide or time - consider having mountings screws with large flat heads, or adding fender-type washers under regular wood screws. Indentions for 4 place for the mounting screws are on the underside of the slide - but we used 3 additional since the upper mounting edge did not lay flat at all with noticeable 3/4" gaps that small belts or pockets would get caught on before sliding. Add the 3 extra screws pulled these gaps down to less than 1/4". All-in-all, the slide assembly design makes sense, particularly for shipping in a reasonable sized box....but the poor design of metal plates and holes in the plastic slide at the joint not lining up is a real pain, and could have be so easily avoided...I actually wonder if anyone, anywhere in the production process even tried to assembly just 1 slide unit before just mass producing them and selling them way above their worth for what your get.
Matt Syp
2025-01-01 17:59:16
I know how to put things together. Even difficult things. But this slide is absolutely horrible. The metal brackets don't line up with any of the holes and the curve isn't even cut properly to allow the brackets to sit in place. This company should be ashamed of themselves over the poor quality of their product and the sellers should be ashamed to carry this product at all. Unfortunately I am past my return window so I have lost my money.There are many other slides on the market that are better. The one I currently have was more complex to put together, but went together easily. This one is not worth the time and effort you will have to put into it.
NeftalÃ
2024-12-28 10:15:28
VenÃa roto lo tuve que devolver
Recommended Products
$422.00
$ 99 .00 $99.00
$422.00
$ 99 .00 $99.00
$172.21
$ 69 .99 $69.99