Shopping Cart

Your cart is empty.

Your cart is empty.

Tedlar Bag 1L - Air Sampling - Gas Sampling - PVF film - Polypropylene fitting valve (Pack of 10)

Free shipping on orders over $29.99

$120.00

$ 59 .99 $59.99

In Stock
  • Capacity: 1 Liter - Size: 7'' x 9'' - Material: 2 mil Tedlar PVF film - MADE IN USA
  • Our Tedlar bags utilize a patent pending 2-in-1 fitting. By combining a shut-off valve and Teflon-lined septum, you are able to fill the bag and remove the sample for analysis with one fitting. The stem is used to connect 1/8” ID tubing for filling and emptying the bag. The septum can be used for removing the sample using a syringe. Fittings are available in polypropylene, stainless steel, and Teflon.
  • Guidelines: 1. Store Tedlar bags in a clean area away from potential contamination sources. 2. Tedlar bags are designed for use at atmospheric pressure. Over pressurization (>2 psi) can cause the bags to burst. 3. Always ensure the bag, fitting, and tubing materials are appropriate for the compounds being sampled. 4. CEL Scientific does not recommend reusing Tedlar bags in most cases.
  • To fill the bag: 1. Connect the appropriate tubing (1/8” ID) from a sampling source to the stem on the side of the fitting. 2. Open the valve by holding the stem and turning the top portion of the fitting counterclockwise one turn. 3. When the bag is full (approx. 90% capacity), close the valve by holding the stem and turning the top portion of the fitting clockwise until it is finger tight.
  • To withdraw the sample using a syringe: 1. Insert the needle into the red septum on the top of the fitting. 2. Withdraw the sample and remove the needle, the septum will reseal itself. (Do not allow the needle to pierce the Tedlar film on the back side of the bag)


CEL Scientific gas sampling bags are made of DuPont's 2mil Tedlar PVF film. Tedlar PVF film is tough, durable, and considered chemically inert to a wide range of compounds. Bags of Tedlar film can be used for indoor air sampling, hazardous waste sites, leaking underground storage tanks, stack sampling, soil gas sampling, gas blending, calibration test standards, and most other gas sampling needs. All of our stock bags feature an eyelet and our patent-pending single 2-in-1 fittings that combine the valve and septum into one. We offer polypropylene, stainless steel, or PTFE fittings, contact us for custom sizes.


CENTRO DE BIOINFORMATICA Y BIOLOGIA COMPUTACIONAL
2025-09-05 10:22:21
Excelente cumplimiento y calidad de los productos
J.J. Scott
2025-06-22 10:10:28
I've ordered these a few times, and have never had any issues. All collected samples were viable when tested at the lab.
Curt Publow
2025-06-18 14:29:34
Bags were ok, price is good, but I think it is hard to be 100% sure the valves are closed tight...
Customer
2025-05-22 11:23:14
Was what I needed to take gas samples
CENTRO DE BIOINFORMATICA Y BIOLOGIA COMPUTACIONAL
2025-05-02 10:09:33
Excelente cumplimiento y calidad de los productos
J.J. Scott
2025-04-28 11:59:21
I've ordered these a few times, and have never had any issues. All collected samples were viable when tested at the lab.
Curt Publow
2025-04-12 13:11:35
Bags were ok, price is good, but I think it is hard to be 100% sure the valves are closed tight...
Customer
2024-11-23 11:39:46
Was what I needed to take gas samples