Your cart is empty.
Your cart is empty.Jenni
2025-09-02 13:51:33
Used this for my classic Fiat Spider 124. When I order my center rocker panel it said it was made with original tooling, but none of the wholes were dimpled, so I bought this to remedy the situation. Was slightly small for my application, which is not the tools fault, so I just made sure to keep the body panel nice and level on the press and it worked great.
Dave Downing
2025-08-31 15:52:08
Works perfect Hole size right on the money. Thanks for the fast delivery.
Kevin
2025-08-29 13:48:15
I used this to flush mount a drain on the plasma table. Worked perfectly
samantha simons
2025-08-28 11:47:56
Hole size is 1/8 linch arger for conduit keep that in mind. Work's great us it in a Knock out punch
Jenni
2025-08-15 14:27:05
Used this for my classic Fiat Spider 124. When I order my center rocker panel it said it was made with original tooling, but none of the wholes were dimpled, so I bought this to remedy the situation. Was slightly small for my application, which is not the tools fault, so I just made sure to keep the body panel nice and level on the press and it worked great.
Dave Downing
2025-07-21 20:23:26
Works perfect Hole size right on the money. Thanks for the fast delivery.
Kevin
2025-07-11 17:40:39
I used this to flush mount a drain on the plasma table. Worked perfectly
samantha simons
2025-07-09 15:52:11
Hole size is 1/8 linch arger for conduit keep that in mind. Work's great us it in a Knock out punch
Rick W. Stone
2025-07-07 19:04:05
Good heavy piece and it worked very well.
Ernest johnson
2025-06-10 13:02:07
This is about 1/2inch too wide for the shaft on the knockout. This makes it impossible to screw anything to the shaft. Worked well with a 5/8th bolt. But I still would rather have one that works with the knockout.
Denis
2025-06-09 15:01:43
Used this dimple die on my frame boxing plates. Plates were 3/16" thick. It did need about 25,000 psi to press
Tim Buchholtz
2025-06-05 14:01:19
Worked flawlessly with a harbor freight hydraulic knock out punch.Highly recommended
Customer
2025-06-01 11:13:17
Build well good tools
Arno U.
2025-05-30 16:31:59
Die Version „1/2" conduit size / 0.86" actual size“ hat folgende Abmessungen:Männlich: 11,2x21,3x28,9x37,0mmWeiblich: 11,3x21,8x29,8x36,9mmMit 0,5 Zoll hat das absolut GAR nix zu tun; die 0,86“ (21,844mm) „actual size“ passen immerhin ein bisschen zum Zapfen bzw. dem (ursprünglichen) Loch im Blech.Zum Pressen eignet sich eine Schraube M10x65. Besser noch UNF 7/16“-20 x 2 3/4“, da größerer Querschnitt und feineres Gewinde. Die Schraube muss (für 1,5 mm Stahlblech) nicht mal hochfest sein. Einfach mit einem langen Ratschenschlüssel anziehen (z.B. 60 Nm), fertig ist der Kragen. Mutter, Gewinde und Scheibe gut schmieren, damit sich die Schraube nicht mitdreht und es keinen Verschleiß gibt.Nach 20 Kragen noch keine nennenswerte Abnutzung, das Werkzeug wird geschätzt noch hunderte weitere Male halten. Sehr hartes Material.
bruce peters
2025-05-28 10:43:50
Product arrived in good condition. However, it is the wrong size. The packaging says " 1.25", but the die is 1.75". I will keep it, as I can use it on other projects, but is useless for current project. I gave it one star, as it does work well.
Rick W. Stone
2025-05-25 13:17:26
Good heavy piece and it worked very well.
Ernest johnson
2025-05-06 13:04:01
This is about 1/2inch too wide for the shaft on the knockout. This makes it impossible to screw anything to the shaft. Worked well with a 5/8th bolt. But I still would rather have one that works with the knockout.
Denis
2025-04-26 13:03:39
Used this dimple die on my frame boxing plates. Plates were 3/16" thick. It did need about 25,000 psi to press
Tim Buchholtz
2025-03-31 11:14:52
Worked flawlessly with a harbor freight hydraulic knock out punch.Highly recommended
Customer
2025-03-28 10:15:13
Build well good tools
Arno U.
2025-03-26 18:51:39
Die Version „1/2" conduit size / 0.86" actual size“ hat folgende Abmessungen:Männlich: 11,2x21,3x28,9x37,0mmWeiblich: 11,3x21,8x29,8x36,9mmMit 0,5 Zoll hat das absolut GAR nix zu tun; die 0,86“ (21,844mm) „actual size“ passen immerhin ein bisschen zum Zapfen bzw. dem (ursprünglichen) Loch im Blech.Zum Pressen eignet sich eine Schraube M10x65. Besser noch UNF 7/16“-20 x 2 3/4“, da größerer Querschnitt und feineres Gewinde. Die Schraube muss (für 1,5 mm Stahlblech) nicht mal hochfest sein. Einfach mit einem langen Ratschenschlüssel anziehen (z.B. 60 Nm), fertig ist der Kragen. Mutter, Gewinde und Scheibe gut schmieren, damit sich die Schraube nicht mitdreht und es keinen Verschleiß gibt.Nach 20 Kragen noch keine nennenswerte Abnutzung, das Werkzeug wird geschätzt noch hunderte weitere Male halten. Sehr hartes Material.
bruce peters
2025-01-05 17:10:37
Product arrived in good condition. However, it is the wrong size. The packaging says " 1.25", but the die is 1.75". I will keep it, as I can use it on other projects, but is useless for current project. I gave it one star, as it does work well.
Recommended Products
