Your cart is empty.
Your cart is empty.Please review all product information to ensure that this product is compatible with your unit.A Message to the CustomerOur staff constantly strives to provide clear and concise product information. We understand that sometimes it can be difficult to confirm product compatibility. It is your responsibility to confirm this is the correct product you need; therefore, we encourage all customers to fully review the information provided in this listing prior to purchase. Nothing is worse than having to return a product, trust us...we get it. Let's work together to avoid this! If you are unsure as to whether or not this is the correct product for your unit, please ask. If you seek assistance we will need as much of the following information as possible, if applicable, to help you find the product you are looking for: Model and/or Sub-modelSpec and/or Type NumberCode and/or Serial NumberYearEngine HorsepowerOur knowledgeable product specialists are always willing to help you verify product fitment.Stay rugged, my friend.
S. J.
2025-08-17 18:27:41
I installed two of these in an Evenrude 6hp outboard (circa 1974). Installation can be tricky because if you mount them where the old breaker points once were mounted you MUST make sure the connecting wires are very short and closely tied down. this mounting is underneath the flywheel. The first time I installed these I did not make sure the wires were trimmed closely and they got RIPPED apart in an instant. So the next time I trimmed the wires very close and made sure they stayed out of the way of the flywheel. Now the motor runs great. No points to file, no dwell to set. Just plug and play.
James h.
2025-08-13 10:13:54
Good product thanks
Customer
2025-07-02 10:32:21
Fast shipper
Dan & Teresa Thompson
2025-06-19 13:52:03
1st module did not work. Troubleshot and could not get it to fire. Swapped out just the modules, leaving wiring in place and 2nd module worked great. Removed module and replaced with 1st one just to be sure and it would not fire again. I had plans for both modules, so I am a little bummed one did not work, but the other one worked great and my old HH120 Tecumseh starts and runs so much better than with Points & Condenser.Easy installation, need a magnifying glass to read the instructions, but they aren't hard. 1 wire grounds behind module mount, other wire to ignition coil. If module doesn't fire, reverse connections. Easy!
Customer
2025-04-20 12:39:22
USED ONE OF THESE TO REPLACE A NOVA MODULE FROM LIL RED BARN THAT I HAD JUST INSTALLED AND THE NOVA MODULE FAILED AFTER ABOUT 5 CUTS. SWAPPED IT OUT WITHH ONE OF THESE AND CUT A LOAD OF WOOD-RAN PERFECTLY. LIL RED BARN NEVER MADE GOOD ON THEIR PROMISE TO REPLACE THE PART-1 SENT IT BACK AS WAS TOLD TO DO AND EMAILED WITH NO REPLY BACK. MUCH BETTER PRICE ON THESE ALSO.
Tosa
2025-03-02 15:40:37
Late review. Bought in May of 23. I tried to use these igniter modules on several old Chrysler outboards to replace the points and condensers. Just could not get them to work. I'm not saying they don't work I'm saying I can't get them to work. I'm missing something or I'm probably doing something wrong. I put back the points and condenser set it up and the outboard runs.
Darwin Moulton
2025-02-23 19:18:08
Finally had a chance to work on the Simplicity Landlord mower today and after installing the new carburator I checked on the old points and condenser. After checking them out I went in the shop and pulled out one set and installed the unit. The unit was easy to install, the directions were clear and easy to follow. After it was installed I gave the engine a small shot of starting ether and the engine roared to life. Going the cover the wires with wire loom for a more finished appearance , but really pleased with my first time using this product.
ken
2024-12-14 15:48:50
The media could not be loaded.
Rob
2024-12-01 11:11:33
I used two of these on a 1969 Evinrude outboard. Just remove the old points and condensers. Connect the coils to the kill switch wires. Connect one of the ignition modules to one wire and one to the other. +to the kill switch wire and the - to ground. No other adjustments required. This 18hp motor runs at 35km/hr now.
Recommended Products
