Your cart is empty.
Your cart is empty.Product Description
Multi voltage and color to choose from
- Light Color: White, Red, Yellow, Blue, Green
- Rated Voltage: 12V, 24V, 110V
110V/24V/12V Energy Saving Indicator Light
Mounting Hole Size 8mm
- LED for energy saving and low maintenance cost.
- High strength and durability for long use.
- Simply drill a hole and install with nut and washer.
- Flush mount for easy connection and strong conductivity.
- Material: Plastic, Zinc Alloy
- Mounting Hole Diameter: 8mm / 0.31 inch
- Cable Length: 200mm / 7.9 inch
- Thread Length: 8mm / 0.31 inch
Simple Installation
Panel mount for easy connection and strong conductivity. Simply drill a hole and install with nut and washer.
Energy-saving
Energy-saving and low maintenance cost. Impact resistance, corrosion resistance, vibration resistance.
Applications
These panel mount indicator lights are suitable for replacement of signal lights, and also the working status display of household appliances, switch valves, industrial equipment, etc.
For Home Appliances & Garage
From the water heater, the boiler system to the garage door, they will show the open and close status of the door or equipment. Add these indicators to any circuits.
D G
2025-08-28 10:36:28
This was a factory fit for a vintage, and quality, surge protection power strip I have. The old invandescent indicator that told you it was on at a glance was almost out, and this fit perfectly in the same location. It also is holding up to the mains voltage just fine(so far). The strip is a heavy use one that runs my workbench, all lights and equipment as well as another strip for tools as needed. So far, so good.The wires are extremely thin, use a fine stripper and coat the ends in solder to make a more solid connection with your work piece.Cant ask for more for the price, though I miss the old RadioShack days...
Diesel Soot Todd
2025-08-10 13:38:51
Used this in a PID enclosure for a DIY powdercoating oven.Pretty nice quality although a bit expensive for what they are. The wires are probably around 28ga… forget normal strippers. Use your teeth or quickly burn the ends with a lighter and pull the insulation off.
Peter S.
2025-07-26 16:47:10
It took 5 minutes to drill the hole in my ceiling fan and connect the LED to the switch do I could see when the fan was actually off.
ElJuezJubilado
2025-03-24 16:37:52
This LED indicator works fine, but the tiny (28 AWG?) leads are difficult to connect to other wires or points. I had to solder to get a good connection.
Stephen Newman
2025-03-13 17:06:00
LED pulled out of the holder on both pieces taking them out of the package. I had to use silicone to secure them. They functioned properly once secured.
SixOfOneATL
2025-03-10 16:10:31
Glad I tested these before installation. These are supposed to have a resistor under shrinkwrap on one leg of the LED and a diode on the other leg (LEDs don't like being reverse-biased hard, which they would be at 110VAC). The first of the pair that I tested on a variac started to smoke and bulge at about 70VAC - turned out it was missing the diode. I ran the other one up to 120VAC (our typical line voltage) and it was fine.
JD Weiss
2025-03-02 20:06:53
I have a clear (yellowish) rock that we want to put on a base and illuminate from below, as an accent piece. Combined, the two lights we purchased are not bright enough to do this. The lights would work well for what they were originally designed for, but not for what we want to do. So, back to the ole' drawing board and begin another search for a suitable light source.
Mary Hilger
2025-02-04 11:56:55
Bulb will not stay in holder, mounting nuts do not fit so no way to mount. Total waste of money
Recommended Products