Your cart is empty.
Your cart is empty. How to choose the right size: O.D 121.3mm,Check the Centre Bore (CB) data of the wheel you have on hand. This can be found on the box label. If CB cannot be found on the box or back of the wheel, measure the center hole’s diameter using a caliper. Inner Diameter116.7mm(I.D.) Not sure exactly what size hub-rings you need? Don't waste time and money guessing. Just send us a message with what wheels you have, what make, model, and year of vehicle you have, and we will be happy to recommend the correct hub-ring for you. How to install: Insert the Hub Centric Rings into the wheel center bore and then install it onto vehicle wheel hub. Q&A Q: What is the tolerance of these Diameter data?
A: Normally accept ±0.1mm. So:
56.15=56.1; 60.06 = 60.1; 64.15 = 64.1; 66.06=66.1; 66.56 = 66.6; 72.56 = 72.6; 74=74.1
Q：I chose the right size, but Why can’t I push hubring into wheel, or push it onto Hub?
A: Hub, hub ring, wheel are fit each other tightly, So they can’t fit in when there is rust or dirt on the Hub, or some rough edges of the hub ring or some paints over sprayed onto wheel center bore. So sand these slightly with a sand paper and try it again.
All-Awesome
2025-09-05 16:42:50
They fit my 2024 Silverado EV and Fuel Wheels perfectly.
JR
2025-08-15 16:31:13
Hard to find the right hub ring online, but these aluminum hubs fit my 2004 Ram 3500 SRW one ton ram exactly with 18 inch Vision Nemesis III machined finish wheels (152.2 mm hub bore, apparently like all Vision wheels). And the price ($40) was way better than any other aluminum hub sellers that ranged from $70 to $100. And they arrived 12 hours after ordering them.The seller says these fit 121.3 (or 121.2) and mine measured the former, but my SS calipers are not a dial model so could be a hair off. These hubs are a nice fit in the wheel hub and just a tiny bit less tight on the truck hubs, but more than adequate to help center the wheel while mounting and probably underway to take some weight. These model rams have a hub with just a tiny bit larger diameter inside (next to the center of the truck) so if you use calipers to measure, take the wheel off entirely.Be sure to put the wheels back on while the axle is still on the jack stand and tighten each lug nut sequentially to the opposite side nut and torque to specs (135 ft. lbs for this model single rear wheel SRW one ton).
Vitalino Arroyo
2025-07-29 11:35:29
Great price perfect fit Dodge wheels on Chevy
Kenneth Kotula
2025-07-17 16:59:36
Great fit on my 2014 Ram 2500. Shipping could be better! No reason my package left Nashville and went to Florida when it was supposed to come to Kentucky!
Jesse
2025-07-15 13:19:07
Got it, popped them on, fit on there. Nothing really special about these.
Mel
2025-07-07 20:10:28
Fits my 2016 ram 2500 great.
Kara Mooneyhan
2025-06-24 11:08:00
Worked perfect on my 2018 Ram 3500 (Srw), used with fuel wheels
Eric bauer
2025-06-20 13:20:26
I have aftermarket 18inch XD rims on my truck, when I ordered the rims off Carid they came with plastic O rings(lasted a couple years) it was hard to find the correct ID/OD. At first these tight because the amount of surface rust and brake dust, take a red scotch bright pad and clean the wheel hubs, and they fit perfectly with my Duramax. ID/OD 117/125.
Jose Allen
2025-05-05 10:09:46
Finally no more vibration.
Gary Guo
2025-04-10 18:50:01
good quality
Nicholas M.
2024-12-12 11:17:06
Perfect !
Recommended Products
$12.69
$ 6 .99 $6.99