This is probably the 4th one I’ve gotten, for me and some family members. Very practical and space saver.

This is as described, is very light and sturdy, fits perfectly on the door, I have a long ironing board and it and the iron firmly.

We just got this iron rack. At first, I hung it over the closet door but I disliked the sound of the ironing board banging and clunking when I opened the door so I just now installed it on the wall behind the door. It was very easy to install with a drill - it took less than ten minutes. Unfortunately when I tried removing the iron and board, the rack popped off the wall. The screws didn't hold the rack to the wall tight enough. Luckily I had some washers, so I used those and that seemed to secure it to the wall.My iron fits pretty tight into this rack and I'm gonna see if I can loosen it up a bit. Also I want to see if I can remove the hanging clip because it's in the way now that I have mounted this on the wall. I had to bend it at the bottom to get the ironing board on.Overall I'm glad I purchase this. But it should come with washers for the wall mount to secure it more tightly and the slot for the iron should be wider.

Good job

Works just fine easy to put together

I got this so I could finally get my ironing board and iron out of the basement and stowed on the 2nd floor, where all the closets and bedrooms are.Right now it is hanging on the back of a closet door--which is just fine.The over-the-door hanger strip is sturdy enough and slender enough that the door still closes.The caddy itself is not great. It's also not horrible. It's flawed. The price is more than reasonable--so perhaps its flaws are not fatal ones.HARDWARE:I have every intention of screwing this gizmo to the solid wood door, as my old board and big Rowenta iron are hefty. So I checked out the screws provided. I have solid 1" + doors and I measured . . and think the screws supplied will pop out the other side of the door, so that's not happening! (Search on for better hardware.)For the record, the screws (4) do come with plastic wall anchors---but IMHO you would want to use MUCH more robust hardware to hang this on a sheetrock wall and expect it not to pull out with the weight of a board and iron. Much. More.Design flaw, but you can get around it.IRON STORAGE SPOT:My iron sits in its space with lots of room--a bit too much room! It rocks back and forth towards and away from the door and also a bit side-to-side. I finally figured out if I were to pull the heel of the iron out beyond the lower "rests" it would wedge in and not move so much.The wings at the sides of the iron's body are also set rather widely apart. About 4" of a gap. Not so much of an issue with an iron like mine that has a wide sole, but if your iron is slender it might not work as well. Again, design flaws.BOARD HOLDER:My worst problem with this item is that I have the sort of ironing board with Y legs.Yes, you can bend the holders out to the sides to accommodate that.No, it doesn't take much in the way of muscles.But once you've bent the holders out, it's difficult to seat the board, as the distance between the "nose" of the ironing board and the bottom of the iron is much reduced. Almost to nothing.You have to lift your board up and over the hooks before settling it back down in--and there is little to no room to do so. It catches. In fact, fiddling with it causes the entire caddy to come out from the door and swing around, making the process worse. (I assume screwing it to the door will fix that.) This all bounces the iron askew in its place, which is going to happen no matter how the caddy is attached.This is slightly over my shoulders, so if you are older and have problems lifting weight with your shoulders, or shorter than maybe 5'6" that may be a challenge.Hangers that were just 2" longer would solve the problem.Again, design flaw. Rather a big one.FINALLY:If you have T legs on your board, and don't mind the wobbling of an iron slightly above your head, then this will work very well for you and be well worth the price. I, however, would not purchase this again. Somewhere out there . . . there's a better caddy for heavy Y boards. Meanwhile, this'll gotta do for now.

It fits nicely over the door and I keep the iron in the housing just below the hanging partI did have to bend the tines a little bit, so will hold the ironing boardIt’s a great purchase solid build looks great

I ordered this over the door ironing caddy. Was so disappointed to have it arrive and not fit my particular ironing board or iron. I contacted the company and almost before I pushed submit, they had contacted me about refund. No questions no hassle . While the product did not meet my needs, it was very easy to hang and sturdy. I would recommend the product and will say the design of my ironing board is not like most. I had not noticed before but the leg structure of the board is not like any I have seen before

I was happy that this worked well for my ironing board with curved base legs and a larger iron.The only thing I have to find a solution for is the fact that the bottom of the ironing board slams against the door when I open and close the door.

Tiene buenos acabados y sostiene muy bien en la puerta, es metálico con pintura brillante, se ve durará muchos años

Muito prático

Produit très pratique pour le rangement d'une table à repasser dans un petit espace.

Great product and would buy again