Your cart is empty.
Your cart is empty.Wixey Model WL133 Drill Press Laser
Vincent M. Hoang
2025-08-30 11:42:17
The media could not be loaded.
mike
2025-08-06 18:57:01
Easy to set up, useful. Batteries last. Slid around on me, requiring sometimes re calibration/adjusting back to center. Made it stay in place better by putting thin cardboard under the hose clamp that holds it.
Ira
2025-07-15 17:43:28
The Wixey Drill Press Laser works very well. I had no trouble mounting it, or adjusting it to get repeatable accuracy to about 1/32". I would have given it 5 stars instead of 4 except for one annoyance. I found myself constantly forgetting to turn it off, and running the batteries down. I finally fixed that problem by replacing the two AA cells with a 3V AC-DC adapter. To do this, I had to install a suitable jack in the rear of the battery compartment and move over a few wires. (see photo).As claimed, the device can be adjusted to produce crossing lines independent of the height of the workpiece, It does so by producing two crossing planes of illumination, each approximately perpendicular to the drill press table. The “z-axis adjustment†changes the tilt of each beam to make it perpendicular to the table. However, the supplied adjustment procedure is slow and inaccurate. I have found a better way (see photos).Set the table to be about 12†from the lasers. Place a small mirror on the drill press table so that each beam is reflected upwards. Use small object (approximately 4†in height) to hold a small piece of wax paper to intercept both the direct and reflected beams. If the “z-axis†is not properly adjusted each beam will produce two parallel lines - one line is from the direct beam, the other from the reflected beam. Adjust the “z-axis†screw so that the two lines coalesce. At that point the beam is bouncing perpendicularly from the mirror. Repeat for the second laser. The whole process is very fast, and there is no uncertainty as to when the two lines overlap.
NachoJ3sus
2025-06-25 18:09:25
Google it and watch the video online for setup. Super simple and accurate to use.
Paul Hinds
2025-05-19 18:54:05
Other than the fact that vibration seems to make the adjustment of the Z-axis go off after a while, this little bugger is really great. Getting it back into alignment is trivially easy but should not be needed.NOTE: reviewers who say the focus changes when raising and lowering the table clearly just did not read the directions. When set up properly, the focus stays exactly where the bit will hit the wood regardless of how much you raise and lower the table. My own complaint is that this focus DOES change over time but that has nothing to do with raising and lowering the table, it is, as I said, a matter of the vibration moving the z axis.Installation and setup are very simple and straightforward. Directions are clear, simple, and concise.It's a pleasure to use and really simplifies drill press use.
Merle S. Long
2025-04-27 14:12:20
This laser guide is perfect for my rebuilt 1955 Delta 17-600 drill press. It fits up tightly under the head unit and stays out of the way. The mount is very rigid and I did use the included extension because my press is large. I built this press as a major upgrade from the modern press I was using but that one had a laser guide built in so I was very happy to discover that Wixey made this unit to be retrofitted to presses without one. I have several Wixey products in my shop so I knew the quality would be good. Though it looks a little dim in the photos, the laser lines are bright and very visible. Follow the simple instructions to fine tune your adjustment and it will be spot on. Another reviewer mentioned that he replaced the batteries with a 3v power supply and that's what I did. Now I don't have to worry if I leave it on and I won't be spending a ton on batteries. It would be great if Wixey offered a corded version of this unit for us professionals. Batteries or no, this is a great laser guide.
N21K
2025-04-01 10:43:56
Quality is not too bad, but the knobs are hard to turn and adjust (1 star off), making it difficult to get centered. Once you do, its very accurate. I managed to change the height 10 inches and still have less than 1/4 mm shift.
Gregg Brichan
2025-03-22 15:44:42
This laser sight for the drill press is excellent. Easy to install. Easy to adjust. Just don't forget to turn it off when done.
Paco
2025-03-18 16:45:27
Â
guido lanzillo
2025-03-08 12:05:36
The media could not be loaded.
ã®ã¿ã•ã‚“
2025-02-09 17:35:34
æ€ã£ã¦ã„ãŸã‚ˆã‚Šè‰¯ã„商å“ã§ã—ãŸã€‚
paul282
2025-02-05 14:50:10
Die Einrichtung ging einfach und gut, allerdings sollte man eine exakten 90° Winkel haben und vorher sicherstellen, dass der Bohrtisch senkrecht zur Bohrachse steht.Die Schlauchschelle gibt an der Tischbohrmaschine eine scheren Halt. Dann wird ein ebenes Brett mit einem senkrechten dünnen Strich versehen und auf den Bohrtisch gestellt. Das Brett muss ebenfalls exakt senkrecht stehen, andernfalls stell man falsch ein und erhält in unterschiedlichen Höhen einen Versatz. Wenn Brett und Linien entsprechend genau stehen, werden die Laser mittels der kleinen Schrauben in den Drehknöpfen senkrecht ausgerichtet.Anschließen spannt man einen Bohrer in die Maschine und setzt einen kleinen Punkt auf ein ebenes Probestück. Mit den Drehknöpfen werde die beiden Laserlinien auf den Punkt ausgerichtet – fertig.Zur Kontrolle empfiehlt es sich in verschieden Höhen zu kontrollieren ob die Bohrspitze den Punkt exakt trifft.Für den „Hausgebrauch“ ein gute Hilfe um die Bohrungspunkte gut zu treffen. Selbstverständlich gibt es auch Grenzen, schon allein aufgrund der Laserlinienstärke.
Client d'
2024-11-26 18:41:40
Pour perceuse à colonne.
Recommended Products
