Your cart is empty.
Your cart is empty.Product Description
-
Note:
Low battery in the receiver may cause inaccurate results. Replace with new batteries and remove them if unused for long periods.
Karyna
2025-09-02 15:27:54
Great tool to have around if you work a lot with electricity,wires,receptacles,switches and breaker boxes. Makes the project less complicated. Helps you a lot if your home/apt breaker box has no labeling.
Mario Pereda
2025-08-28 21:54:40
Good quality material I recommend them
waz
2025-08-25 11:11:07
Me gusta porque te ahorra muchas maniobras. Con la localización de circuito
Wayne
2025-07-03 15:29:00
it beeps everywhere and i got to fall to trial and error. the so called learning process is barely usae
K Butler
2025-06-13 12:23:26
I knew this product wasn’t going to work when I picked it up out of the case. It’s probably like $0.15 of material. The instructions are inadequate, so I watched a video of a circuit finder from a different manufacturer. I tried it 10+ times on different outlets and it never indicated with any accuracy. The rapid beeping that is supposed to identify the circuit occurred at 5+ circuits. Just unreliable. Spend a little more money on a reliable manufacturer.
LG
2025-05-03 15:41:34
I really like this item for the price. Works very well. What people complain about is the mis identification of breakers. I find that what is missing on the other brands is the sensitivity knob that this unit has. This enables you to pinpoint the exact breaker in your panel. Start with the sensitivity all the way up till you get a signal then start dialing it back till you home in on the only breaker. Works great. I also identified a ground fault circuit that had no ground passed to the other outlets in the chain using the plug in device. The electrician never jumped the ground to the next outlet opening the grounds to all the outlets in the chain. This properly identified the problem and I was able to fix it fast.
ET
2025-04-28 16:55:36
Really want to like it but it doesn’t perform well to identify Circuit breakers. I compared this to my other KL*** finder, even that one is not perfect but it works a lot better to positively ID the CB. I tried the different sensitivity settings multiple times but still not able to pin point the CB. Too bad. I like the NCV feature and that works well with 3 different sensitivity selection. It comes with a nice case too. However it fail to do what it suppose to do mainly ,at least not the best. I will stick with my kl*** finder for more expensive and return this one.
Dave Evers
2025-03-02 17:16:49
Most electrical panels don’t have good info as to which breakers go to which outlets. This tool lets you plug the sender into an outlet, then go to the master panel to locate the breaker it is on using the sound from the receiver.I find this is really only practical as a two-person job unless you are only locating one or two outlets. I suggest taking an hour or two with a spouse or a friend and mapping the whole house; using the following procedure:1) draw up a diagram of all the rooms in the house with the rough location of all outlets. I then identify each outlet on the drawing with a letter from A to Z (if you have more than 26 outlets, just start over with AA to ZZ). This helps reduce confusion in later steps.2) make two copies of the drawing; one for the inside person (at the outlets), and one for the outside person at the main panel.3) have 1 person go to each outlet in the house and plug in the sender. Then contact the other person using a phone or walk-in talkie (or a lot of yelling) and let them know the transmitter is installed in the outlet and the corresponding letter ID. The outside person can then find the appropriate breaker using the receiver; and write the corresponding breaker number on the drawing. It will be common for multiple outlets to be on the same breaker - just mark them appropriately on the diagram.4) move on to successive outlets, and continue until all outlets have been identified. Then you will have a complete map of which outlets are controlled by which breaker. I suggest creating a final diagram using a program like Paint; and printing out multiple copies as well as maintain a digital copy that can be stored on phones, in the cloud, wherever. Put one copy in the main panel so you’ll never again have to guess which breaker goes with which outlet.
Jose
2025-02-02 20:51:21
Excelente producto
Richard
2025-01-31 17:37:48
Easy to use
Adolfo Córdova Moreno
2025-01-23 19:16:08
Se aprecia calidad en la manufactura. De ensamble sólido y duradero.
Daniel Eduardo Villarreal RamÃrez
2025-01-04 17:18:23
La tapa vine floja y no engancha,donde va la 🔋, cuelga la pila
el.pinche.vapor
2024-12-09 10:03:26
Muy buen producto, solo que si es algo tedioso el tema de regular la sensibilidad del equipo. Pero en general es un excelente equipo.
Recommended Products