Your cart is empty.
Your cart is empty.Product Description
This false shafts pad is made of PORON material, with a back glue on the bottom. After removing it with tweezers, install it tight in the false shafts hole.
Suitable for PCB satellite shafts and steel plate satellite shafts, as shown in the figure for operation.
Anson
2025-08-25 10:10:39
Each leveler is 2 7/16" long when set into its non-slip sleeve. The steel pipe measures approx 3/32" in diameter and has an opening 1/16" in diameter, easily accommodating a typical stabilizer wire.Include are also 24 small poron stickers for applying the Holee mod to stabilizer stem housings. I haven't tried these as my stabilizers don't exhibit any rattle, and my space bar and stabilized keycaps sound great once leveled and lubed with Krytox 205g0.A thin 5 5/8" x 1 1/8" case is included to hold the pipes and stickers. While it's a nice touch, it's far too big for the tool and stickers so I'll repurpose it for something else.I have been leveling stabilizers with just my fingers but the process seems more precise with an inexpensive leveling tool like this. I used the tool as soon as I received it as I was just about to build a Tofu60 2.0 board and had some Durock stabilizers on hand. While the wires were straight, I did find that two of the stabilizer wires needed leveling so I used this tool and got them as perfectly level as I could, simply by apply some twisting force to the wire. Job done!I can see these tools becoming very handy for future builds and for revisiting stabilizers I installed in other keyboards.
woozle
2025-08-24 14:42:22
The handles come without the grips attached, but it is simple to do, then you're off to balancing wires!
Rzr
2025-03-09 13:38:53
Good tool to fix stabilizer wires. Housing is metal with plastic covers and really help you to twist stab wires to correct any bends. Do note this will only help align the bent ends of the stab wires and not a curve in the wire itself.Comes in a case, but it could have been much smaller.
Anson
2025-02-07 11:24:01
Each leveler is 2 7/16" long when set into its non-slip sleeve. The steel pipe measures approx 3/32" in diameter and has an opening 1/16" in diameter, easily accommodating a typical stabilizer wire.Include are also 24 small poron stickers for applying the Holee mod to stabilizer stem housings. I haven't tried these as my stabilizers don't exhibit any rattle, and my space bar and stabilized keycaps sound great once leveled and lubed with Krytox 205g0.A thin 5 5/8" x 1 1/8" case is included to hold the pipes and stickers. While it's a nice touch, it's far too big for the tool and stickers so I'll repurpose it for something else.I have been leveling stabilizers with just my fingers but the process seems more precise with an inexpensive leveling tool like this. I used the tool as soon as I received it as I was just about to build a Tofu60 2.0 board and had some Durock stabilizers on hand. While the wires were straight, I did find that two of the stabilizer wires needed leveling so I used this tool and got them as perfectly level as I could, simply by apply some twisting force to the wire. Job done!I can see these tools becoming very handy for future builds and for revisiting stabilizers I installed in other keyboards.
woozle
2024-11-15 10:10:41
The handles come without the grips attached, but it is simple to do, then you're off to balancing wires!
Rzr
2024-11-13 10:41:55
Good tool to fix stabilizer wires. Housing is metal with plastic covers and really help you to twist stab wires to correct any bends. Do note this will only help align the bent ends of the stab wires and not a curve in the wire itself.Comes in a case, but it could have been much smaller.
Recommended Products