Your cart is empty.
Your cart is empty.This matching Tongue and Groove router bit set cuts a 1/4" Thick tongue into stock up to 3/4" Thick. The cutting depth is 1/2" And the shank diameter is 1/2". The set is pre-shimmed and comes in a handsome wooden box. Additional shims are included in case further adjustments are necessary.
Kathy Agar
2025-09-02 12:43:10
Nice and sharp. Perfectly sized parts upon assembly. Good value, not a professional, should give me years of use.
Sandra
2025-08-05 15:21:13
Worked well. Clean cutting in fir. Nice box for storage.
KaitLynn
2025-07-28 12:43:42
I will start by saying that I like these bits. As other reviews state, they aren't perfect. I used them to make shaker style cabinet doors out of 3/4" premium pine and, after using several pieces of scrap, decided that there was no way to get them to not leave a small shaving of wood on one edge of the board when using the tongue cutter. However, this was easily removed with a sharp chisel and, after sanding, my doors look great. So, while you might not have that one extra step by going with a higher priced set, these worked great for my needs and the price was a big bonus. I will gladly trade the 60+ extra dollars for a small amount of chisel work.
EddieRock
2025-07-27 12:57:28
I had 3 different widths of hardwood floor and they were from different manufactures and because of this, the grooves were different sizes. I used these in my router to make them fit together perfectly! Don't try to use these without putting your router in a table. It just won't work. I purchased this really crappy Router Table https://www.amazon.com/dp/B07X1RKLSW to put my router in and used these bits. It worked great.These bits never got dull and are really well made. I would highly recommend them for putting tongue and groove in oak flooring on both the long AND short edges of the floor to fit them together.Pros:Well madeSharpAccurateCons:Simply hard to get out of the case. Yah, they are in there goodI highly recommend these bits. The brand is amazing!
Gambit
2025-07-11 13:10:22
Worked as expected.
Jaybird
2025-07-05 14:18:18
I have used several times. they are sharp and do a great job.
Tiffany
2025-07-02 15:18:52
I have several different types of Yonico bits. They all work as expected.
Mark Vermont
2025-06-19 19:20:11
I bought these to Machine about 450 feet of one by five one by six one by seven and one by eight spruce and red pine lumber into tongue and V groove panelingRouting went fine other than you really have to tighten down hard to avoid them slipping in the collet. That sucked a bit
Chris
2025-06-18 18:48:28
3/4 shank works great
Scott Ward
2025-05-30 11:44:57
Used to tongue and groove but joints on 800 square feet T&G pine. Expected a bearing to blow or become dull. Quality was way more then I was expecting. I cleaned them up and expect o could do another 800 soft! Awesome!
juan bautista galaviz campos
2025-04-29 13:41:07
Me gusta usar esta marca de brocas porque el filo dura mas que el promedio de otras brocas.Buen producto
Jonathan Beaulieu
2025-04-11 20:15:40
Rien à dire
Gabriel Cerecedo G
2025-02-08 17:52:01
Las compre para amachimbrar madera para una pared, hacen la hembra y macho con una cara en "V" muy adecuada para pared o piso. Muy buen filo pues cortan perfectamente sin astillados. Las recomiendo ampliamente pues son Yonico. Se puede usar en contrachapado de 18 mm, tablas de 3/4", 7/8", 1/8" etc. Yo ya hice mis patrones para estas medidas, asà que cuando lo requiera, calibro la altura con mi patron adecuado rápidamente y fácilmente.
Recommended Products
