Your cart is empty.
Your cart is empty.**USA STOCK** This brand new digital speedometer is specifically designed to replace the stock speedometer of a RPS (Ricky Power Sports) Hawk 250. The cluster offers indicators for all of the following: RPMs Speed (KM/H and MPH) Turn signals High beams Fuel level Low fuel level Gear indicator (N, 1-5) The cluster also comes with a digital speed sensor designed to replace the stock analog speed sensor. It is calibrated to the Hawks 21" front tire. Installation is simple: Remove the stock speedometer and speed sensor Mount the new cluster and speed sensor Plug in the new speed sensor to the cluster Plug in the cluster to the existing stock wiring harness (this will give you everything you had with the stock speedometer) Run wires for the RPMs and gear indicators (1-5) to the wiring harness next to the battery. Plug in the pins and you're done.
Keith
2025-09-02 12:18:17
Nice upgrade for the Hawk 250. Easy to install and everything works perfectly. The speedometer reads very high when set for 21" wheel, but when I set mine for a size 17" wheel, it reads 55 mph when going 55 mph verified by GPS. Yes the fuel gauge reads empty when there is about 1/2 tank of fuel left in tank, but that may be the result of the sending unit in the tank rather than the display. Not a big deal since the fuel tank has a reserve valve. Mine has lasted over a year and 1200 miles without any issue.
Michael
2025-08-16 16:48:15
The media could not be loaded.
Mitchell W.
2025-06-09 14:53:30
Installed it on my 2020 RPS Hawk 250. Check out the YouTube videos for installation instructions. I don’t know how I rode without it. It’s great to see what gear you are in too. Display is bright and super easy to read - even the smaller numbers are bright and clear. See both rpm and speed in s single glance. I do have an 1/8 in gap between the new sensor and the front wheel hub. Was hoping for a closer fit to keep out water and dirt. Since there are seals around the front wheel bearings I don’t think this will be a problem over time. It comes with settings for 17, 19, and 21 inch front wheels. I have s 21 in wheel but set it to 19 in for better speedometer accuracy. Very happy with this purchase.
Frank DeGregorio
2025-06-05 12:27:50
Definitely higher quality than the one that came on the original hawk 250
Ralph
2025-04-30 12:52:46
I installed this on a 2023 BSR Raven 250.The individual wires are removed from the plug with the help of a small jeweler's type screwdriver.On the front connector just match up the colors except for the red/white wire, it needs to be joined with the blue/white wire.FRONT: red/white to blue/whiteAt the rear connector once again match up the colors except for the light green/red stripe, it joins the green/red stripe wire from the wires you removed from the original plug to make the "N" light work. The blue/white wire joins the blue/white wire in the other plug at the battery position and the purple is unused.REAR: light green/red to green/redYou will need to remove a small section of the mounting plate to allow for the wire harness (don't forget to paint your cut to prevent rust).Everything works just fine but at 60mph on the new speedometer, the GPS speed is 55mph. I haven't tried to adjust that yet, but I will in the future.
toy
2025-03-29 17:13:42
super easy install, 1 page instructions. the screen is back lit all the time so that is great on sunny days. love the gear indicator and tach upgrade. having minor trouble selecting mph from km, next day i figured out that it needs to be displaying ODOmeter first.2 turn key off then on while holding the reset button. 3 let go after three seconds. And it will change. im super happy. took less than 1 hour, hardest part is taking the front wheel off to swap the speed cables by my self with no motorcycle jack.
Samuel D Stewart
2025-01-02 11:29:26
Poor directions...
Pakman
2024-11-25 14:47:19
I'm giving 5 stars for simplicity, but it will not work as is for X-Pro model other than intended Hawk. I own a RXE 250 wiring is completely different. I have to sort out every circuit and figure out how I will make this work on RXE. But it's 20 degrees outside have to wait to milder weather and a few hours with nothing else to accomplish. This is on my back burner.
Recommended Products
