Your cart is empty.
Your cart is empty.Product Description
240 Degree Replacement Motion Sensor
Detection Range: Adjustable up to 60 ft. (18m), varies with the surrounding temperature
Sensing Angle: Up to 240-Degree
Electrical Load: Max. 300W Incandescent Lamp. Max 72W LED DRIVER/ LED Bulbs
Power Requirements: 120 VAC, 60 Hz
Operations: TEST, AUTO, D2D, MANUAL OVERRIDE Mode, 10-second to 10 mins Time Delay
Working Temp ℃: -30~50 ℃
Practical Motion Sensor with 4 Modes, More Choices for You!
TEST MODE: No matter day or night, it will turn on when motion is detected, and off after 5±3 seconds when no motion is detected. Tests the sensor’s functionality even during daylight hours.
AUTO MODE: At night, the motion sensor turns lights ON automatically when motion is detected and OFF after a preselected time delay
D2D MODE: Integral photocell effectively works to prevent it from activating during daylight, works automatically in the dark.
Manual Override Mode: Turn the wall switch OFF and ON within 2 seconds, devices will keep ON for 8 hours, auto turn off at dawn.
Stepless Adjustable
The control of sensitivity and time has been upgraded into stepless, which means that you can set the sensing range at 10 to 60ft and lighting time at 10s to 10 minutes, and anywhere in between.
Easily adjust the motion sensor to different angle based on your DIY requirement. Light wherever you want!
The durable and weatherproof design ensures safety for outdoor/indoor use protecting from rain, sleet, or snow. Perfect replacement motion sensor solution for porch, yard, front door, garage, driveway, entryway, walkway, step, hallway, etc.
Kindle Customer
2025-08-29 16:45:13
Worked as should, easy to install.
Jake NYC
2025-06-24 12:03:07
Easy to install and set up, can be added to a non motion light to make it motion sensing. My fixture only had Dawn/Dusk function, but I didn’t need the light on all night so I added this.
Alan
2025-05-25 12:19:33
This motion sensor arrived on time , was easy to install and worked immediately. Only issue is that the space at the top of the threads on the mount is too thick for a metal electrical box. Had to add a large o-ring so it would tighten.
Professor Ed
2025-04-25 12:38:00
My motion sensor spotlight fixture has been faithfully serving for decades, but the sensor finally failed. Michigan's snow, ice and frigid temperatures took their toll. I shopped for a fixture replacement and the were $50 or more, so I decided to buy this sensor unit and replace the one on my fixture. It took about 15 minutes and worked perfectly.
Lynn
2025-03-26 15:05:46
After 2 months lights turn on randomly with no motion even with the sensitivity turned all the way down
Michael
2025-02-19 19:20:56
Great motion detector and easy to install just 3 wires and I feel like it’s a good value for the money but it does have a short arm so be aware of that I replaced one with a longer arm but this one works fine in my case
DesertDweller
2025-01-24 18:28:00
This has been one of the most reliable motion sensors I have ever tested. It appears to be sold under several different brand names, they are all excellent. The rounded 240 degree sensor is an improvement over traditional 180 degree sensors, and the PIR based trigger has a low rate of false positives. This detects humans every time, but is not triggered by stray headlights from vehicles, wind, or other similar natural movement.I like using this type of standalone sensor because it can be wired up to multiple lights, and multiple motion sensors can trigger the same array of lights. I used 14/3 wire, where the hot is connected to the black input of the motion sensor, the red output of the motion sensor is connected to the hot input of each light and then also ran to additional lights as well as additional motion sensors. This allows for any of the motion sensors to trigger all lights on the circuit whenever any of them detect motion. It's a great setup for security and illuminating larger outdoor areas.My only complaint is that these can not handle much current. The say only 72 watts of LED lights or 300 watts of incandescent. This isn't much if you are running multiple lights, so larger light arrays will require a relay. This is unfortunate, I would love to find a motion sensor like this one that could handle the same load as 14 gauge wire, or around 1,400 watts at 120 volts. So far I haven't found anything like that, this is the best available for now.
W. C. Russell
2025-01-01 13:03:21
I bought two of these to turn the lights on in my home shop (a 16 x 24 out building). I ended up having to wire in a bypass switch because the photoeye loses me and the lights go off. I am clearly in view of both eyes (wired in parallel), but it takes a fair amount of motion to keep them on. On the flip side, it seems like bugs activate it because the lights go on when no one is out there. The building is tight, so no vermin or birds can get in. Bugs or a defect are the only possible explanation for false triggers. There are occasional crickets and flying bugs, so that's my bet. I have played with the range and sensitivity but haven't hit a good compromise.
Cliente de
2024-12-13 13:52:26
cumple lo que dice sobre la detección distancia y rango de sensibilidad. Lo uso para encender luces en una escalera y puerta de entrada de Garage cubre perfectamente los 180 grados y la distancia de un lado son 6 metros y del lado contrario son 10 mts funciona bien al encender las luces para la entrada del auto y para subir o bajar las escaleras y entrada a la casa
Recommended Products