Your cart is empty.
Your cart is empty.Product Description
Learn More About 2pin 8mm COB Connectors
DIY Strip to Wire Quick Connection Updated version of LED strip connectors, assemble wire by yourself as needed, flexible to different project! No need to solder. Just clasp your prepared led strip section into the connector to get connected. compatible with 30-120 LEDs/M strip, made of flame retardant material, safely use. Support high current LED strip lights.
Q:Do these connectors work with 24V system?
A: It would be ok for the connector to work with 24V system.
Q: Which type of light strip is suitable for?
A: 8mm width single color strip lights with 2 Soldering Pads. both IP20 non-waterproof and IP65 waterproof light strips
Q: How should I connect the light strip?
A: You can pierce the strip light from the front. For IP20 strip, it is recommended to pierce from the front of the light strip.
Q: If I accidentally cover the connector, how can I open it?
A: You can pry it open with a suitable screwdriver.
Unique design, easy installation
Upgraded strip to wire connetor
High-quality copper parts and solid materials ensure that the pin needle can effectively pierce the wire and the light strip. Compared with other connectors, the performance is greatly improved.
Suitable for IP20 COB strips
These 2pin led light connectors are suitable for 8mm single color COB LED strip lights
Reusable/ extension
The unqiue design is convenient for inspection or reinstallation, just use a suitable screwdriver to pry it open, and can be reused and expanded.
How to use the 8mm 2-PIN COB connector
1. Insert wires into the guide slot
and then press cap down
2. Align the Soldering Pads of the light strip surface with the pins on the connector. just please align the positive and negative poles of the light strip
3. Make sure the ‘+’ and ‘-’ polarity is correct.
4. Wire to led strip connection complete.
More applications
Biantie La 2-Pin 8mm COB LED Strip to Wire Connectors
These 2-pin strip to wire connectors are a solution for 8mm COB LED strip lights connection and extension needs, allowing you to create custom lighting setups with adjustable extension distances and angles.
Diane K Rost
2025-09-05 12:28:14
Very easy to connect.
matt
2025-09-04 17:01:41
Bought these connectors because a different connector caused the lights to flicker, this connector works great. Gets a perfect connection and doesn't cause the lights to flicker.
Patrick B.
2025-08-27 11:44:38
Worked perfectly.
Warren Claassen
2025-08-24 17:15:40
If you knew to buy these you probably had a good idea of how to use them but without instructions the first thing to is figure out orientation. They show pictures of the two folding sections for the wiring and the LED strip but don't make it terribly clear that the folding sections are down toward the backing side of the LED. I would also want to insert the LED fully into the housing but then the spade in the connector wouldn't press into the center of the pad on the LED so I don't really know if I truly connected them the best but they do work. It does need 22 gauge wire as if you drop any smaller it will not bite into those and stay connected.They are working so far and were pretty easy to install.
Michael
2025-08-01 18:13:12
used them for my auto LED lighting kit and they worked great.
Chuck
2025-07-09 20:06:46
UPDATE:One of these started getting intermittent. I tried squeezing it tighter, which didn't really work. I tried reseating the cables and recrimping with it, which didn't work. It just refused to make good contact. I ended up just soldering the wires directly to the LED strip. The other two connectors that I used are working fine, for now.These seem to work pretty well when new, but the real test will be how they are doing in 5+ years. They are easy to use. Just make sure the led power pads line up with the little clamping pins. The pins are semi-destructive to the pads, which is a bit of a downside, except that it ensures a good connection. Also make sure to use the right gauge wire on the other end.The clamps do fairly securely snap into place, so make sure you get it right the first time. They can be unsnapped, but it's easy to damage the locking mechanism. I also would never use these in an installation that moves regularly. It may be possible for these to open up with enough movement over time.
James W. Allison
2025-05-19 14:26:36
I installed two different sets of COB LEDs using the 8mm Biantie connectors, and didn't have an issue with ANY of them. SO much better than my previous experience with LightingWill connectors, which always suffered from intermittent connections.One thing - Biantie says that the connectors can be pried open with the proper-sized screwdriver. That's a true statement, but what Biantie DOESN'T mention is that just because you can reopen the connectors DOESN'T mean that the connector can be reused after it has been "unsnapped". The tiny plastic tabs/nubs that lock the connectors in the "closed" position have a tendency to shear off when the connector is pried open, meaning that the connector won't lock "closed" again.
Karen Jubie
2025-05-11 18:03:40
Directions were incorrect. None of the wiring worked according to installation direction. A wast of $90. Contacted the seller and received no response.
Mauricio Ramirez
2025-04-28 11:04:57
No los eh instalado espero funcionen a lo esperado pero se observan jien hechos.
Logicweb
2025-04-27 11:01:41
Répond à mes attentes
SquirrelGirl17
2025-04-06 10:20:07
These worked great! They were easy to use and even without knowing exactly what I was doing with these connectors I rewired my strip lighting perfectly!! No sodering or wire stripping required!
George Sincovich
2025-04-01 19:41:58
Product is a good design, I just find that if you're connections are not right the first time, its hard to re open these connectors, and then to re install. otherwise they worked well for my purpose.
Erick Chateauvert
2025-02-09 17:13:05
Facile d’utilisation et rapide !
Recommended Products