Your cart is empty.
Your cart is empty.Product Description
Anton Volkov
2025-08-30 14:56:49
Used to press a transmission apart (between a C channel plate bolted to the bell housing and the input shaft). Worked great!
Peter
2025-08-01 16:19:42
I have only used it once but it did the job. The fitting is correct for a Enerpac and put out a few tons of pressure without issue. It will take years to properly evaluate this cylinder but for the one time it was needed..... it did not let me down.At this price point - Highly Recommended.
Anon Amuse
2025-06-20 14:21:47
10T 26mm/1.0" Stroke Hydraulic Cylinder Low Profile Jack Multi-Section Ram Jack Lifting Cylinder for Machinery Ship Bridge ConstructionReceived the 10-ton cylinder only. Believed I was also to receive the hydraulic pump body with hose. Went back and read the “About this item†description which does state it consists of the pump body and hose. The photos do show only the lifting cylinder. I then looked through all the other ad options. They used the same “About this item†description for all purchase options. This is very misleading. Each purchase option is very different from another. They need to redo this ad to have the description conform to each option. In the meantime, be very careful and pay attention to what is in the photo graphics, which is probably what you will actually receive. I did not have a hydraulic pump to operate this cylinder. I figured a compatible pump would eventually be listed for selection and that did happen.Now that I have a pump, I was able to test the cylinder. The cylinder seems well built. It is solid, heavy and extends to 30mm. Ad and label on cylinder state that it extends to only 26mm. I did not put it under load yet, so maybe under load conditions it only goes to 26mm. I expect to use this setup in leveling the foundation of my house. There are places where this small cylinder will be the only tool I will be able to use.Because of the confusing ad which misled me into thinking I was getting the complete hydraulic jack setup, I am giving this only 3 stars. If the ad had been correctly stated in describing the cylinder only, as received, I would probably have given this item 5 stars.
Clayton
2025-04-09 13:10:52
there isnt much to review on this. It works as it should, without any leaks. i havent tested the max lifting capacity, but it lifted both items that i used it on.
Brutus
2025-03-29 17:04:07
Stout and solid unit. Feels and looks well made. Quick coupler hooked right up to my hand pump from another manufacturer. No leaks. Smooth operation. Pay attention to the size, the 10t I ordered is small and with a 1" stroke will often need blocked or shimmed to do what you want. But it is what I wanted for tight access work, Occasionally I need a smaller unit where my other rams will not fit.
Customer
2025-03-12 11:17:42
The MMNZE 10T 26mm/1.0" Stroke Hydraulic Cylinder is a nice addition to my old porta-power set.I do a fair amount of steel construction and repair, and there are times when the longer rams just won't fit into a small space, and levers or mechanical spreaders just aren't powerful enough. This has already come in handy for straightening a twisted trailer frame.As an Amazon Vine reviewer, I received this 10 ton 1" ram free of charge. That being said, with a price of $80 for the ram only and $120 for the ram and pump, I think the combination is a better value.
Where's Waldo
2025-02-27 13:59:09
I picked up the 10T, 1" cylinder without the pump, as I already have a pump for these. I use them for a few different things, but mainly some work on vehicles from time to time - like removing a stuck front wheel bearing assembly.I haven't used this one yet, as my opportunities are few and far between, but I did hook it up to my pump, made sure it stroked, and used it to lift the rear of my big riding mower a bit. Obviously, with the 1" stroke, I blocked it up until I was in contact with the mower, pumped it up the full 1", and let it sit. It pumped up just fine and didn't bleed down while I cooked a couple of steaks on the grill, so I'll call it a success.
Tyler Forge
2025-02-20 13:58:09
Where’s the pump? I thought this thing was supposed to come with a pump. But no - poor reading comprehension. This 10T hydraulic cylinder was one heck of a paper weight without the pump. It’s heavy and serious and I totally wanted to use it on something, but lack of the hand pump had me thwarted. Sad day. Had to get a pump. Now wow. I have no use in mind for this thing. It just amazes me that this little thing can push so hard. I'm sure it will come in handy someday.
Recommended Products
$221.59
$ 99 .00 $99.00