Shopping Cart

Your cart is empty.

Your cart is empty.

#9 High Temp Roof Flashing Boot, Fits Pipe Diameters 9-1/2' - 20-1/2' Wide, Includes Square Metal Roof Pipe Flashing, Red

4.9 (8) Write Review
Free shipping on orders over $29.99

$180.99

$ 75 .99 $75.99

In Stock
  • INCLUDES - (1) #9 Square Metal Roof Boot | Base Width: 25" | Pipe OD: 9-1/2" - 20-1/2" | Max Temp: 500 degrees Fahrenheit.
  • HIGH TEMP RUBBER ROOF BOOT - Made with quality silicone, this roof boot is designed and tested to withstand continuous temperatures up to 500 degrees Fahrenheit. These boots also hold up well against ozone, UV rays, and other outdoor elements
  • FLEXIBLE BASE - The metal roof vent boot is made with an aluminum base that conforms to any style of corrugated roofing material. Simply adjust the base to fit the shape of the metal surrounding the vent pipe and fasten it using the stitch screws.
  • TIGHT SEALING - This metal roof pipe flashing boot kit also includes a tube of urethane sealant from NovaFlex that creates a tight seal between the roof vent pipe boot and the metal sheet.
  • EASY INSTALLATION - The chimney pipe boot is designed with clear diameter marks on the rubber for easy identification and cutting to fit around your roof pipe. Ideal for a metal roof stove pipe boot, chimney pipe boot, and other high-temp vents.


Product Description

ST Fastening Roofjack Square Silicone High Temperature Pipe Flashing Boot
  • Rated for -100ºF to +500ºF
  • Flexible Aluminum Base
  • Easy to Use
  • Water Diverter

Marked so they can easily be cut with shears to fit exactly the pipe size used.

Square RoofjackSQ can be turned so corner is pointing up the roof. It will act as a water diverter.

Fasteners Plus ST Fastening RoofJackSQ

Square Silicone High Temperature Metal Roof Flashing Boot

Manufactured from silicone rubber, the RoofjackSQ is compounded for maximum resistance to ozone, UV light, and temperature extremes.

The flexible aluminum base will allow the flashing to conform to any metal roof configuration. Pipe location can be centered in the flat of the panel or the rib. Urethane sealant and self-drilling screws complete the installation.

ST Fastening RoofjackSQ Roofjack Square EPDM Pipe Flashing Boot
Advanced Ozone Resistance Test 70 hr @ 500 pphm
High Temperature Resistance Intermittent Test +260ºC (+500ºF)
High Temperature Resistance Continuous Test +225ºC (+500ºF)
Low Temperature Resistance -74ºC (-100ºF)
Tensile Set Maximum 5MPa (700psi)
Compression Set Maximum 50%

Che h.
2025-09-04 13:17:23
It really is heat proof I put it to the test on a wood stove showed no mercy on it didn't even flinch
Marcus
2025-08-24 12:11:36
This product is very well-made and was simple to use. I recommended highly.
Brady
2025-08-20 15:27:44
Easy to use. Quality. Build Quality is good. Fit is good. Functional.
Charles D. Hansen
2025-07-10 12:40:32
Works a needed
Sandra Atchison
2025-03-17 16:43:10
Haven't installed it yet but it appears to be good quality and should suit our needs just fine.
JR
2025-03-10 15:09:23
Boot seems to be good quality but it doesn't work for a 10/12 pitch with a 10" pipe. It doesn't give you much information as to what it will work for in the description. I had to cut it and try to install to find this out. Expensive lesson.
Curtis Boone
2025-03-03 16:21:35
This boot was exactly what I needed to seal my furnace vent — I got just what I needed— good quality
Customer
2025-01-11 11:24:47
Â