Your cart is empty.
Your cart is empty.Uses hook and loop sand paper, for additional sandpaper use Karebac Stearated aluminum Oxide part numbers 66830, 66832, 66833, 66834, 66835, 66836, 66838 through 66841. Perfect for balusters, handrails, wood moldings, Countertop edges and many other applications. Karebac makes a full line of abrasives for the automotive, woodworking, marine, glass & Marble Industries. We also carry a line of tools to be used with our common products. Our innovative designs are the perfect start to the perfect finish. All products are 100% satisfaction , see manual for information.
Bruce
2025-07-09 15:00:48
My project (well, FIRST use...) is a 1976 Alfa Romeo Spider - with lots of curves and grooves. This sander is ideal for those "blood grooves" down the length of the sides, and the headlight tunnels. You can pick from a wide variety of curves amongst the blocks, slap it on the power head and add your appropriate weight of paper (all hook and loop attached). Roll sand paper with hook-and-loop backing works great.Operation is fairly low air usage, and "just right" when adjusted for speed (air flow knob).Price seems fair.
Patrick E.
2025-07-08 11:15:47
Finally found the time to use this and was super excited because I’m refinishing a set of teak furniture…At first it worked great but then it just stopped and air is coming out but no action.. tried shaking it because I have a feeling it’s the cylinder that’s not working…So works great when it works but didn’t work for long unfortunately
Richard S. Fay
2025-07-06 18:28:04
This is a good tool. I had 39 hardwood cabinet doors with bead profiles to sand and refinish. This straight line profile sander was a hand saver. The tool is quiet. Vibration and noise level is significantly less than my electric sanders. My only question is why didn't I have one of these years ago. If there was a source for the tool only without the profile set, I'd likely buy a couple more. The velcro pad holding works so well that the pads can be a little tough to change. Not a complaint but I'd rather have multiple tools already set up. This was one of those great purchases.
Allen
2025-05-03 17:58:49
This is a great little tool to have if you sand anything with contours! I haven’t had it long but have already used it a lot! I repair boats and the lines in them can get pretty busted up rebuilding them takes time and this tool saves time! Well worth it!
Jenn Bird
2025-03-30 14:28:07
I was so excited to get this and at first it worked great and I was thrilled but after using it to sand two railings it started shaking and something inside broke. I was really hoping this would have worked
jeff
2025-03-20 12:17:01
Previously submitted one star review due to difficulty getting the device to run. Seems to need to be shaken so piston inside is setting just right before it will oscillate, otherwise, just sat there hissing, and no amount of pushing/pulling on pad would coax into motion. Finally discovered it needed to be shaken a bit each time I picked it up to use it.Left message with seller a few weeks ago. No response. Suddenly, today, I'm told a new one is being sent as a replacement, and I could simply send old one back in same box. Will see how replacement runs and report back.Must address - another reviewer had problems with velcro. Not sure why - there is one style of it to adhere specially shaped pads to the sander, and another on the face of the profile pad for sticking sandpaper to. I had no problem with either one.When it runs, it does do a good job of sanding cross-grain wide - belt sander pattern on doors and face frames. (no trim profiles yet) Seems a little faster than random orbit, which I still use for a quick, final sanding prior to finishing.
Zamecnik
2025-02-15 10:24:32
I’m giving this product 3 stars only because I really like the concept of it, but in the end the hook and loop they use on the backerpads is horrible and does not hold the paper which pretty much makes this sander useless when constantly having to turn it off and reattach the paper, very frustrating. The pads are poorly made to besides the hook on them which is almost virtually smooth the biggest square pad isn’t flat, also wish their was dust extraction capability. With that said I’m going to try and see if I can replace the hook on all the pads and possibly try and make a block in between the sanders and pads that I can attach a vacuum too which will also require me to drill holes in all the pads. Overall pretty disappointed
Brent B.
2025-02-06 09:28:52
Great for sanding milling marks out of moldings
Recommended Products
$99.00
$ 39 .99 $39.99
$99.99
$ 40 .99 $40.99