Your cart is empty.
Your cart is empty.Product Description
Specialty - Engine & Ignition
-
Harmonic Balancer Puller Set
Easier Removal Of Damper Pulleys In Tight Engine Compartments
This ARES Harmonic Balancer Puller Set provides you with everything you need to remove damper pulleys in tight engine compartments without removing the radiator. With steel construction, you'll have the extra strength and enhanced design you need to get the job done. Whether you're working on a Chrysler, GM, Mitsubishi, Cadillac, or Oldsmobile, this set is the right fit.
The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked. -
Master Harmonic Balancer Install Kit
Inclusive Coverage For Installing Balancer Pulleys On Domestic & Import Vehicles
The ARES Master Harmonic Balancer Install Kit includes a threaded driving stud, a heavy-duty driving nut with thrust bearing, 12 threaded install adapters in both metric and SAE thread sizes, four long-reach threaded press rods, and a heavy-duty case for easy storage and transport to install harmonic balancers on most domestic and many foreign vehicles. Featuring solid steel construction with a black phosphate finish for enhanced strength and durability. Note: Harmonic balancer installer only.
-
Ratcheting Serpentine Belt Tool Set
Removes and Installs Spring-Loaded Belt Tensioner Pulley Model Serpentine Belts
The ARES Ratcheting Serpentine Belt Set is a comprehensive set of tools and accessories, constructed of durable Cr-V Steel with chrome and black oxide finish, suited for removing and installing serpentine belts. It has a ratcheting wrench that allows for easier torquing, and a long extension bar that mates with the ratcheting wrench for maximum extension, allowing adjustments in cramped and obstructed spaces. This set is perfect for makes and models with a spring-loaded belt tensioner pulley.
The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked. -
5-Piece Magnetic Swivel Spark Plug Socket Set
Easier Tune-Ups In Tighter Spaces
This ARES Magnetic Swivel Spark Plug Socket Set easily removes and replaces spark plugs with extra length and leverage for hard-to-reach areas. The interior magnet on each socket grips spark plugs tightly without wearing them down. The heavy-duty retaining ring provides superior durability and strengthens the swivel joint to keep the socket intact. Made of durable, heat treated, Chrome Vanadium Steel, with Chrome plating in addition to its 360-degree swivel action for maximum flexibility.
-
Offset Extension Wrench Set
Zero Degree Swing Arc for Confined Fasteners
The ARES Offset Extension Wrench Set is a versatile, impact-ready tool set that includes 10 low-profile sockets and can be used with impact or pneumatic wrenches to help you tackle fasteners in tight spaces. Made of sturdy steel and high-quality, lightweight aluminum, this wrench is built to last, and thanks to its zero-degree swing arc and chain-driven design, it has you covered for jobs ranging from water pumps to A/C compressors to transmissions and beyond.
-
2-Piece Offset Spark Plug Boot Removal Pliers Set
Easily Remove Hard To Reach Spark Plug Wires
The ARES 2-Piece Offset Spark Plug Boot Removal Pliers are 7.5 inches long, made of forged high carbon steel with polished nickel finish, these pliers also have double-dipped textured handles. The single offset removal pliers are perfect for spark plug wires found on GM 3.1L, 3.4L, 3.8L, while the double offset jaws give you access to spark plugs in rear boots on V6 transverse mounted engines. Their 5/8-inch hose opening also allows you to use these pliers to grip hoses, thick wire, and more.
Zach K
2025-07-16 09:52:11
I used this engine barring tool to get my 1998 12V Cummins to rotate to the correct positions to adjust valve lash. Upon reading other reviews I made sure to “lube†between the tool and the plastic sleeve before use. I just used WD-40 to get some lubrication between the two. As for the fit of the tool it slid in perfectly with a few light taps and had no play in any direction. The teeth seemed to fit/engage very well and got the job done. I was able to turn my engine over no issues and completed the entire valve lash job in a half hour (being rather meticulous, I just installed a new cam). Once complete, I checked over the tool for any imperfections, the only thing I noticed was a bit of the finish wore off the tool where the teeth engaged. No problem at all, I could see this too lasting for many, many uses. If you are in the fence about which barring tool to purchase I would definitely recommend this one. Cheaper ones run the risk of not lasting and more expensive ones have your popular name brand markup. Ares has a very good customer service team and will even reach out to thank you for you purchase and see how their tools worked for you. Overall great experience. I’ll add a picture of the tool after future uses if I remember
Robert LaChance
2025-07-03 16:18:01
The media could not be loaded.
Corey Leary
2025-06-10 14:03:55
So I got this tool to help remove my harmonic balancer that was destroyed. I put a light coat of grease on the plastic sleeve and it looks just as good after the job was done as it did when I opened the box. Great little tool to have and just make sure you remember to double check it is removed before starting your truck. I used this for my '99 Ram 2500 with the Cummins.
Sheila
2025-05-21 17:10:24
Very disappointed, way too much play and just slipped on the flex plate. Useless.
Jerry
2025-03-12 13:08:08
I choose the ARES tool and it has held up to multiple complete rotation of my engine while still in the truck!It was priced in the median price range. It was well worth a few extra dollars and did the job the more expensive tool would have done as well. Used on 2017 Ram high output Cummins.
M. Miller
2025-01-15 11:08:28
This tool has worked really well for me. I greased the wear sleeve and even after a few different uses it's isn't chewed up and is in good shape. Fits perfectly.
wheat farmer
2024-12-03 09:00:45
Works on john deere engines such as the 13.5 and 9.0
Aaron williams
2024-11-22 17:43:05
The teeth do not fully engage with flywheel, watched just the edges. it will turn the engine over but the fit is real sloppy compared to the OEM cummins tool.
Recommended Products