Your cart is empty.
Your cart is empty.Product Description
Key Features:
- Made from woven glass fiber heat resistant matting
- One mil aluminized materials making it ultra-weightless while providing a long-lasting seal
- The strong adhesive back composite makes application quick and easy with a long-lasting seal
- Sustain and screen off direct heat of 400 degrees Fahrenheit and radiant heat of up to 2000 degrees Fahrenheit.
Application:
This insulating cool tape is convenient for application on cables, hoses, wires, fuel lines, and other surfaces. It can also be used to wrap wirings, seal air boxes, cover seams, and secure panels.
Lightweight Insulating Tape
Reflective Solution
Withstand Radiant Heat
William Brown
2025-09-07 19:09:35
Very high quality. Very heat reflective with a thin corrugated adhesive backing . I used it to make a heat shield for the back of an expensive large screen Garmin GPS to prevent overheating on the dashboard in the summer Sun. Perfect results and it stands up very well. Would use it again on anything electronic needing sun protection without hesitation.
Cris
2025-08-26 13:01:00
I used this tape on my Polaris snorkel that was close to the exhaust manifold. The tape had excellent adhesive. It is thick. You can see the fiberglass woven material in the middle and the aluminum exterior. You've got to clean rhe surface area, to which you intend on applying this, before applying the tape. That's just common sense. So for those that complained about it not sticking, you guys had no common sense. I used a rag and rubbing alcohol to clean the surface area.
Shane
2025-08-06 11:26:48
First off the material is nice but the adhesive is garbage. I tried applying it to part of my wiring harness by the exhaust manifold. It was a little cold out so I thought it might be because of that and maybe a little bit of heat you help the adhesive. LIGHTLY warming it with a heat gun made it completely separate from itself. This was adhesive side to adhesive side, foil side to adhesive side, every combo possible. Whats the point of this stuff if the adhesive cant even stay together from sub 150F? If it can't handle light heating with a heat gun hows it going to work near and exhaust manifold? I'm sure the heat resistance of the foil and glass if fine but what difference does it make if you can even get it to stay on? waste of money.
j
2025-04-30 11:41:02
Get a tube of black seam sealer and cover the sticky side of this tape with a thin layer before sticking to things. The glue that comes on this tape is very poor and in the florida humidity unsticks itself rapidly.Other than that the construction is high quality
MH
2025-04-21 13:43:13
When I saw it I was shocked at how thin it was but installing it was very nice and it does the job. I put it on the underside of a saddlebag that goes over an exhaust pipe. It stays cool inside though there's under an inch of space between them. Very good stuff. Great adhesion as well.
Linda
2025-04-06 18:38:08
I cleaned plastic engine components with rubbing alcohol thoroughly, and the tape stuck on well when the plastic was cold, but after a hour drive with engine up to hot temps the tape unraveled itself.It may be useful if able to spiral on a tube with metal clamps, but not by itself. I liked the thickness of this tape, easy enough to manipulate.
P. Riley
2025-04-04 11:35:33
I use this for covering threaded holes when running a robot welder. They work a couple time then they dont stick but worth the money and time it saves running a tap in all the holes.
Bob
2025-03-22 16:01:48
I used this tape to repair the heat shield on my hood. The old clips were hard to remove and I tore the shield at several places. I didn’t want to use a tape that wasn’t heat resistant and this stuff went on great. Very substantial. Good adhesion. I haven’t tried removing it, so I won’t score that attribute.
Super Chief
2025-02-21 18:14:04
Great adhesion and has protected my legs from the exhaust on my bike.
Saif
2025-01-10 12:28:08
It is not sticking on the surface and keeps falling
Recommended Products