Your cart is empty.
Your cart is empty.Product Description
Product Sizes
- Type:M3*0.5/M4*0.7/M5*0.8/M6*1.0/M8*1.25/M10*1.5/ M12*1.75 HSS
- Thread Diameter:3/4/5/6/8/10/12mm, Total Length:51/56/61/70/72/76/86mm
- Square Head Size:(L*W):2.5x2.5/3.1x3.1/4.0x4.0/5.0x5.0/5.0x5.0/6.3x6.3/7.0x7.0mm
- Shank Diameter:3.0/4.0/5.1/6.0/6.3/8.0/9.0mm,Pitch:0.5/0.7/0.8/1.0/1.25/1.5/1.75mm
- Pitch:0.5/0.7/0.8/1.0/1.25/1.5/1.75mm
Hightlights
Material :High Speed Steel
Thread Direction: Left hand
Package Included: 7x Left hand Thread Tap
ifishtoo
2025-08-05 21:55:05
I used one tap to turn a 10 mm bolt head into a 10 mm left hand nut. Some of these cheap tops are not hard enough cut virgin threads but these ones did the job just fine mine is not a production environment so I can't tell you how many threads you'll be able to cut before they go dull. If they do they're fairly simple to sharpen.
Marvin L.
2025-08-03 16:43:02
Nice assortment of metric left handed taps. Of course you can always use your right hand, 😂 but these are for left handed threads. I work on equipment, and lots of times, they tighten by turning counterclockwise, so this is when these really come in handy, for cleaning up damaged threads. I hope you didn’t mind the little humor, but we all need a bit from time to time. Oh speaking of a bit. They also make left handed drill bits. 🤷â€â™‚ï¸
Jack
2025-07-27 16:29:58
Had to tap mirror holes on my Victory Judge to put plugs in. Reverse thread just to make it more fun to find tool to work. Tap worked great with Gearwrench set.
Lars
2025-06-14 12:14:33
Worked good, nice little set of taps. Didn't come oiled or anything but weren't rusty either, I just tapped cast metal on the softer side so I don't know how they perform on harder metals but they came sharp and clean.
William Cochran
2025-06-07 19:55:41
Came on time and work great
Zane
2025-06-01 15:57:41
It's hard to find a source for left hand metric taps. I'm glad I found these. I've used them on brass and steel. So far they cut very well. I cut brass dry and steel with sulfated pipe cutting oil
Thomas Lalle
2025-05-25 18:50:15
need to tap a bushing with left handed threads, i intended to use on an electric motor... to eliminate the gap on a factory threaded axel. the ta; snapped off while trying to tap the bushing.... should not have been a difficult job for the tap.
Rich11
2025-05-22 10:00:30
They worked for what I needed them for. Cleaned out the threads on my miter saw.
Roger Heimpel
2025-05-16 18:56:37
I bought this LH metric tap set to retap a crankcase that had the primary clutch bolt snapped inside. Bombardier outlander 400. After drilling through the snapped bolt, the M12x1.75 tap worked great, using motor oil and using 1/8 turns and then backing off. Very pleased and arrived quickly.
ENPOS E.
2025-04-04 14:16:06
NO SIRVEN PARA NADA, NO LO RECOMIENDO
dieter georgi
2025-03-26 17:01:45
diy-qualität
Vincent Gonnet
2025-02-26 21:02:16
Les taraudages à gauche sont assez rares en mécanique, on les trouve plus fréquemment sur du matériel de jardinage, débroussailleuse et autre. Et faute de taraud, on est bien embêté pour réparer !
CF
2024-12-20 15:40:56
Arrivato orima del previsto
Recommended Products