Your cart is empty.
Your cart is empty.Product Description
Remove old screws
Please follow this picture for the correct screw installation. the top two center screws are different from the rest of the screw sizes.
Remove old glue from surface
Make sure to remove any old glue and debris from the bottom case plate for the MacBook. This will insure that the new rubber feet is not constricted from being installed incorrectly.
Clean surface with alcohol
IMPORTANT: Make sure to thoroughly clean the surface area with a little bit of alcohol. This will remove any previous glue residue and dirt and provide a clean smooth area for the rubber feet to install correctly.
Apply new rubber feet
Make sure to line up the small hole on the rubber feet to the small hole on the bottom case. Press firmly and twist slightly to firmly install the rubber feet. Please do not attempt to remove or test the strength of the glue for 24 hours. This will make allow the glue to adhere to the bottom case properly.
David DeWitt
2025-08-31 18:55:40
Friend gave me his 'crappy and slow' MacBook Pro 2010 after he bought a new machine. The Mac was a little rough, dirty, couple of dents, stickers, old mechanical hard drive and MISSING ALL ITS FEET! It was a sad little Mac. I broke out the alcohol and gave it a good bath, removed the stickers, swapped out the old HDD for a speedy new SSD and purchased these replacement feet to finish it off. The feet were super easy to install, had the bottom plate off the Mac replacing the drive so I installed the feet while I was in there. Done in minutes, easy install, the package came with a screwdriver and some extra case screws which was AWESOME since my sad little Mac was missing 3 of them. I did use my own super glue to attach the backing of the feet to the feet on the inside of the bottom plate but once done, the were the finishing touch on the restoration of a sad little Mac to a bright and shiny, like-new, happy little Mac that I sold on eBay within a half hour of listing it. In short, these feet do what they are supposed to do, love the extras, will buy again if I run across another sad little MacBook.
Key
2025-08-30 18:48:44
These came fast and the screw driver is an added plus (its good quality metal and not a cheap plastic one). The screw set is also nice to have as a backup as they are small and I could lose my original ones at any point.So a few things here:It comes with the back stopper part to attach on the inside of the macbook with glue. My macbook’s (2012 pro 13â€) original feet didn't have these stoppers, the feet were just stuck in normally using adhesive originally.I followed a video and used a lighter to melt the inside part to stay in place.I didn’t use the stopper as my other feet didn’t have them, but its a good idea if you want to keep your feet from falling off and losing them. All you need to do is glue the stopper to the inserted foot using super glue or something similar.
Chris
2025-08-21 20:10:53
I have a mid-2010 Macbook Pro. Over the years, I've managed to lose all of the feet but one, and that one was re-glued to the bottom of the case using contact cement.I bought this kit to replace the feet. The kit comes with the external feet, an internal plug for each foot, a screwdriver, and a small tube of super glue. There's a printed sticker giving a description of the contents, a URL pointing to the official Apple instructions for foot replacement, an email address for support with the company, and a brief blurb describing the business and asking for feedback.The actual process to disassemble the bottom cover using the included screwdriver, replace the feet, and reassemble took me less than 5 minutes. I imagine it might take a bit more if any of the original feet are still attached and need to be removed, but it shouldn't be considerably more. This is an easy and cheap DIY fix that avoids having to make a trip to an Apple store.I highly recommend this product.
Kyle L.
2025-08-18 10:23:49
The screws definitely aren't the same as the OE. The used MacBook I got was missing a couple screws, so I ordered these. The head is not as concave as the OE screws so you have to screw them way further than the originals. Also, I don't understand how the smaller piece for the feet is supposed to work, but the larger piece by itself seems to hold into my MacBook fine. We shall see. But they were cheap and work.
JORGE PELEGRIN
2025-07-28 20:53:48
Good product. My Macbook Pro doesn't move anymore.
TeoMcDohl
2025-04-30 19:41:08
Missing a rubber foot on your Mac (or really, any laptop) sucks because it makes the laptop unbalanced. You can do the animal method and remove all 4 to make it balanced, but then you scratch the crap out of your bottom cover. These were super easy to install and they work. What else can I say?
Alaina Baker
2025-04-10 21:58:12
The included replacement screws are not quite right.Macbook Pro retina display, 2013The two shorter screws are for the hinge area. I dropped one of the original hinge screws during my repair.How lucky, that there's a set of replacement screws included! Except... the head of the replacement screws from the pack (sold with the screwdriver!) have ever-so-slightly smaller stars than my factory screws... just small enough that the (included!) screwdriver pretty much instantly starts stripping the screw, and makes it much harder to actually install it. I was unable to get the replacement screw completely flush with the laptop back, which creates a scratch risk for my furniture even with the feet reinstalled. Be more careful and don't drop your factory screws, as the replacements aren't quite it!
Renato Castillo
2025-04-07 09:43:37
Good product
Constantine
2025-02-11 17:31:26
I bought this set of rubber pads, and they are good, perfectly fit and good enough for the purpose.The screws are rusted and not exactly as the original; they fit into the holes and fix the cover, though. The screwdriver is okay; however, rubber rings are moved around the handle — not much help if a screw is stuck.So the set is just enough if you need rubber pads and look at all the other parts — as of just a "free" add-on.
Erin M.
2025-01-17 18:08:35
I had two feet fall off my 6 y/o mac in the last year and have been keeping an eye on options to replace them. I decided on this kit since it comes with with everything you need - the package contains four feet and inner caps, glue, a screw driver, and spare screws for the mac case. The feet are not an exact match to the original Mac feet in terms of texture; the originals are more of a "stickier" rubber, while these have more of a slick, plastic feel. Size-wise they fit perfectly. The screw driver removed all but two of the screws - I needed to get a heftier screw driver for the last two, which were screwed in much tighter than the others.I watched the video in the provided instruction link, but it does NOT follow the written instructions. The video suggests melting the replacement feet into place with a lighter, rather than glue the backings on to secure them.I did not contact the seller but received two emails from them - one to confirm it had been shipped and send the link for instructions, and a second to resend instructions and ask if I had any issues, which I have not.Photo-Top Row: left close up is original feet, right is from the kitBottom:: feet on left side are replaced with ones in this kit, right side are originals
Brad T
2025-01-14 14:10:09
Easy to install and makes the Macbook Pro feel like new again. Make sure to clean off all the old tape and glue before installing, like in the videos online.
Bcmwolverine
2024-12-25 15:08:00
Unfortunately a few weeks ago one of my MacBooks feet fell off and one was loose so I went to the Apple store. They said it would be $10 a foot to fix and the guy said I’d be best to DIY it. Amazon here I come! This was one of the first products to pop up. I saw it including 4 feet, the plugs to go with them, a proper screwdriver, and the glue. All for under $12! It didn’t even take me 10 minutes to install them. The only thing that took time was letting the glue set. Thanks for an amazing product!!
GDitty
2024-12-12 12:09:05
Good quality feet and screws. Install of the feet was a bit tricky as they really fit only one way...I didn't realize that until struggling with the first foot....otherwise smooth.
Recommended Products