Shopping Cart

Your cart is empty.

Your cart is empty.

BAYCKRC ExpressLRS 2.4GHz ELRS Nano Receiver Long Range Low Latency FPV Receiver for FPV Micro Drone Racing Drone Quadcopter

Free shipping on orders over $29.99

$12.99

$ 6 .99 $6.99

In Stock
  • 1)The BACKY ELRS 2.4G-Nano receivers is an open-source program Based on ExpressLRS, we have 4types RX modules are Released. All of the receivers use the ESP8285MCU.Your Firmware can be upgraded via WIFI, which is more easier.
  • 2) Lowe Latency and High refresh rate,they are very suitable for FPV racing and long range FPV cruising while being ultra-light and ultra-small which made the installation more easier.
  • 3) Usually when you just supplied the power or do not turn on the remote control ,the ExpressLRS can be found hot after 60s by default, then the receiver will get in the WIFI automatically, the LED flashing
  • 4) The BACKY ELRS 2.4G-Nano Receivers is an open-source program based on ExpressLRS,, so any ELRS 2.4Ghz receivers can work with any ELRS 2.4Ghz TX modules , from any manufacture and even DIY ones, this is as long as they have the same binding phase and configuration options( Regulatory Domin, Performance options and Extra Data)
  • 5)About the Fireware about the Bayck Receiver ELRS Receiver ,please noted compatible for BAYCKRC 2.4Ghz , more information ,please contact us , we will reply to you within 24 hours


Item: ELRS 2.4G-NANO


Brand: BAYCK


Frequency: 2.4G FCC(AU,EU Update Firmware)


Chip: ESP8285MCU


RF CHIP: SX1281


Telemetry Power: 20dbm


Maximum Receive Refresh Rate:500HZ


Minimum Receiver refresh rate: 25Hz


Working Voltage: 5V


Weight : 0.6g(receiver only )


Work Protocol: CRSF( Betafilght)


Dimension: 11mmx18mmx3mm


Antenna Connector: IPEX1


Dimension: 11mmx18mmx3mm


Weight : 0.6g(receiver only )


Package :


1x Nano Receiver


1x T-antenna Receiver Antenna


1x Spare shrink tube


4x 30awg silicon connection wires (1black, 1 red, 1 white, 1 yellow)


2 x pin header 1x4



Christopher
2025-09-01 11:33:34
Ordered two placed one on my freestyle tried it come back and ordered two more. Can't beat that price.Nice antenna and love the Holes for a clean placed wire.
James Wareham
2025-08-29 12:31:41
I like the small form factor of the receiver. It was packaged well I received it quickly once ordered. The product performed as expected
FPV Guy
2025-08-24 18:44:52
No issues so far - works as expected.
What The Tech
2025-08-14 10:31:17
I’ll start off by saying I haven’t been able to test this out because I can’t get batteries shipped to my location for my FPV build. However, I will speak to the quality and what you get in the package. None of the items were broken and were packaged well enough. You get everything mentioned, 1x Nano Receiver, 1x T-antenna Receiver Antenna, 1x Spare shrink tube, 4x 30awg silicon connection wires (1black, 1 red, 1 white, 1 yellow), 2 x pin header 1x4. The antenna seems durable enough if it did take a crash. Hopefully in the future I will get the chance to test this out with my build.
Mike
2025-07-23 17:28:06
I get a longer range with this receiver and my picture quality is just as good, too. I don't notice much lag or studdering.
faisca
2025-06-24 12:04:06
Wow, very pleased with this nano receiver. Connected and bound first try. Updated the firmware via wifi without issue. Uses the BAYCKRC 2.4ghz Nano (or possibly BetaFPV 2.4ghz Nano RX) target. Love that it comes with straight and 90° pins, cabling, and clear heat shrink wrap. Most big name manufacturers don't include that much.
A. Fabbri
2025-06-22 10:24:27
This is a very compact and lightweight ELRS RC receiver with an included antenna and most of the accessories you need for a nice install.Likes:- ELRS 2.4Ghz standard. Love having a single controller for all my RC planes.- Included accessories. Stuff you need and no extra stuff you don't: Heat shrink covering, silicone signal wires, and solder-on header pins both in straight *and* 90-degree configuration. Very nice.- Comes with a basic dipole antenna.- Lightweitght and compact. Every gram counts in RC flight and this receiver doesn't dissapoint. Very streamlined design.Dislikes:- Zero complaints so far.Testing:- Besides a basic power-on and pairing, I haven't had a chance for field testing yet due to winter weather, but I'll update this review if I run into any interesting quirks or problems with extended flights.
dbrain78
2025-05-26 10:34:50
I was able to get it updated and bound easily but I'm unable to keep it bound. It will act like it's bound for awhile then it will lose connection. It is very small and lightweight and seems to be good quality but I haven't had any luck getting it to work. I've had no issues with just about every other brand I've used.
Christopher
2025-05-22 10:21:28
Ordered two placed one on my freestyle tried it come back and ordered two more. Can't beat that price.Nice antenna and love the Holes for a clean placed wire.
James Wareham
2025-05-05 13:46:25
I like the small form factor of the receiver. It was packaged well I received it quickly once ordered. The product performed as expected
FPV Guy
2025-04-07 10:31:00
No issues so far - works as expected.
What The Tech
2025-03-02 10:24:23
I’ll start off by saying I haven’t been able to test this out because I can’t get batteries shipped to my location for my FPV build. However, I will speak to the quality and what you get in the package. None of the items were broken and were packaged well enough. You get everything mentioned, 1x Nano Receiver, 1x T-antenna Receiver Antenna, 1x Spare shrink tube, 4x 30awg silicon connection wires (1black, 1 red, 1 white, 1 yellow), 2 x pin header 1x4. The antenna seems durable enough if it did take a crash. Hopefully in the future I will get the chance to test this out with my build.
Mike
2025-02-20 18:28:12
I get a longer range with this receiver and my picture quality is just as good, too. I don't notice much lag or studdering.
faisca
2025-01-31 15:58:14
Wow, very pleased with this nano receiver. Connected and bound first try. Updated the firmware via wifi without issue. Uses the BAYCKRC 2.4ghz Nano (or possibly BetaFPV 2.4ghz Nano RX) target. Love that it comes with straight and 90° pins, cabling, and clear heat shrink wrap. Most big name manufacturers don't include that much.
A. Fabbri
2025-01-24 17:34:35
This is a very compact and lightweight ELRS RC receiver with an included antenna and most of the accessories you need for a nice install.Likes:- ELRS 2.4Ghz standard. Love having a single controller for all my RC planes.- Included accessories. Stuff you need and no extra stuff you don't: Heat shrink covering, silicone signal wires, and solder-on header pins both in straight *and* 90-degree configuration. Very nice.- Comes with a basic dipole antenna.- Lightweitght and compact. Every gram counts in RC flight and this receiver doesn't dissapoint. Very streamlined design.Dislikes:- Zero complaints so far.Testing:- Besides a basic power-on and pairing, I haven't had a chance for field testing yet due to winter weather, but I'll update this review if I run into any interesting quirks or problems with extended flights.
dbrain78
2025-01-23 11:54:56
I was able to get it updated and bound easily but I'm unable to keep it bound. It will act like it's bound for awhile then it will lose connection. It is very small and lightweight and seems to be good quality but I haven't had any luck getting it to work. I've had no issues with just about every other brand I've used.