Shopping Cart

Your cart is empty.

Your cart is empty.

BDS011 Oscilloscope Handheld Digital Oscilloscope Mini Portable Pocket Oscilloscope Kit, 48MS/s Sampling Rate, 10MHz Bandwidth (BDS011 + Clip)

Free shipping on orders over $29.99

$35.33

$ 15 .99 $15.99

In Stock

1.Model:Bds011 + Probe


About this item

  • [ Powerful Function ]: Blapistec BDS011 mini oscilloscope with 48 MS/s real-time sampling rate, 10MHz bandwidth and 128kb record depth, 3.2in TFT full color screen.
  • [ Pocket Design ]: BDS011 digital oscilloscope is mini, portable and easy to hand-held, it's always ready when you need a scope.
  • [ Easy Measuring ]: The handheld oscilloscope equipped with high efficiency one-key switching mode, automatic measurement, easy to use and it is widely applicable in the academic experiment, electronic DIY, debugging and maintenance, electronic engineering education, etc..
  • [ Longer Battery Life ]: Mini oscilloscope build in a rechargeable 1200mAh lithium battery and support Type-C charging, it has an automatic sleep function.
  • [ Complete Trigger Function ]: Auto / Normal / Single 3 trigger modes,it is easy to capture instantaneous waveform.



Product Description

BDS011 OSCILLOSCOPE
BDS011

BLAPISTEC

  • 10MHz Bandwidth
  • 48MS/s Sampling Rate
  • 128Kb storage Depth
  • 3 trigger modes (Auto / Normal / Single)

Details

BDS011

HD Full-view Color Screen

3.2in full-view TFT- LCD display with high resolution.

BDS011

Pocket Design

5.12 * 2.48 * 0.91 in, 0.37 bl, mini and lightweight, put it in the pocket and take it everywhere.

BDS011

Save & Export

It support save and view waveform on the oscilloscope, and it can be connected with PC and share the screen capture pictures to PC, convenient for secondary analysis.

BDS011

Wheel Button

Wheel button design, one-key to switch function and adjust parameter.

BDS011

One-key

Equipped with efficient one-key AUTO setting of all parameters and save the waveform data.

BDS011

Type-C Charging

Built in 1200mAh rechargeable lithium battery, super-long stand by time.

Oscilloscope Specifications

Channels 1
Bandwidth 10MHz
Real-time Sampling 48MSa/s
Record Length 128Kb
Input Coupling AC/DC
Input Resistance 1MΩ
Input Probe Attenuation X1, X10
Max Input Voltage ±400V
Horizontal-Sample Rate Range 1.5Sa/s - 48MSa/s
Horizontal-Sweep Speed Range 100ns/div - 20s/div
Horizontal-Time Base Accuracy 20ppm
Vertical-sensitivity 20mV/div - 100V/div
Low-frequency Response >10Hz
Risinge Time <10ns
Trigger Method Auto, Normal, Single
Trigger Edge Rising edge/Falling edge

DIY nerd
2025-07-20 19:59:48
The media could not be loaded.
JohnR
2025-07-06 18:26:09
Cannot really complain about the low cost for this small handheld oscilloscopeThis weighs very little and has no stand to hold the unit facing towards you, so can be easy for this to slip and fallNegative is the user instructions are lacking for full understanding how to use so you have to test this to find out how best for it to work as you need itAlso, this does not come with a real oscilloscope probe with 2 wires with clips and this would prevent really working on a electronics board with lots of small componentsI used a test tool that allows outputting a set frequency and at what D/C voltageI tested from like 500 Ohms to 10 Mhz.I tested with signals that were sine, square, sawtooth and half-wave and this oscilloscope showed them correctlyThis oscilloscope had no problems locking via auto set mode a receiving frequency but the closer the inputfrequency to 10 Mhz maximum this unit support, the harder it is to lock the signal from moving aroundDo not expect to get long hours of chargeable internal battery, and it does take longer to charge up and youhave to supply a USB charger
CWB
2025-05-29 11:25:23
I would have had a hard time 40 years ago imagining that I would have access to such a portable, affordable little oscilloscope. This won't, and isn't meant to, replace a good quality bench scope but to have something this portable that you can take basic readings with is very handy. The controls take a little getting used to since there are only four buttons and a rocker wheel button that need to be used to access everything. The instructions are not very clear so it does take some figuring out but it is not that difficult. One of the buttons is an auto button which for the most part gets you set up for most of what you need. Mine came with alligator clips which was handy. The screen is pretty bright and clear and easy to see even with my old eyes. It comes with a nice semi hard shell case to make it convenient to throw in your bag and have it protected. It also comes with a USB-C charging cable so that you can recharge its internal battery.
H. Haro
2025-05-27 14:42:26
This is a really nice oscilloscope for mobile use. The USB-C charging really makes it convenient to keep charged. The size also helps since it doesn't really take up much space even with the leads attached. The interface definitely takes some getting used to but it's not bad given the size. The screen is also not great but good enough for automotive use IMO. It is not going to match the performance or easy of use of a full size scope but for the home gamer and at a fraction of the price it will definitely be enough to get you out of a lot of jams. If you don't have an oscilloscope in your toolbox for the price this is a great addition.
Daniel
2025-03-22 15:50:10
Neat little scope. Comes with a nice case and basic set of cables. Was able to use my probes from my Tektronix by changing to X10 in settings and using a balun extension. Keep in mind to only measure up to 40v is using the standard clamps. Will need an X10 probe to measure up to 400v. Had to perform a calibration as the system was slightly off. To enter setup, press the wheel for about a second. Measurements against my Tektronix showed very similar results. Amazing considering how economical this is compared to a Mult-hundred dollar scope. This isn't perfect but is very good at getting a basic scan.
Fonzie Sanders
2025-01-01 13:01:30
Nice little oscilloscope for portable/remote measurements... The usefulness is obviously limited by having a single channel. I'm not sure the sample rate is actually 48MS/s... Looking at a 10MHz sinusoid, you are on shaky ground. Can make out a square wave at about 1MHz.