Your cart is empty.
Your cart is empty.Product Description
BIGTREETECH TMC2209 V1.3 stepper motor driver adopts StealthChop2 ultra-quiet technology. It is an ultra-silent motor driver IC for two-phase stepper motors. Its continuous drive current is 2A and peak current is 2.8A. Compared with TMC2208, the driving current of this IC is not only improved by 0.6A-0.8A, but also this IC increases the function of locked-motor test.
Tips:
1. When the driver is inserted into the motherboard, please pay attention to see the direction of the drive, can not be inserted in reverse, to prevent the drive from burning.
2. Be sure to do a good job before driving heat dissipation work (heat sink + fan), to prevent the drive is not working properly.
3. Pay attention to the wiring sequence and I/O port when wiring. If the wrong line is connected, the driver will not work properly. Please connect according to the Github manual.
BIGTREETECH TMC2209 V1.3 Stepper Motor Driver
Control chip: TMC2209-LA Chip；
Logic supply voltage(VIO): 3-5V；
Motor supply voltage(VM): 4.75V-28V DC；
Peak current: 2.8A；
Current RMS: 2A；
MicroPlyer Microsteps: 1/256；
Operating mode: STEP/DIR or UART；
Configuration: CFG Pins or UART；
Ultra Quiet
BIGTREETECH TMC2209 V1.3 stepper motor driver uses StealthChop2 ultra-quiet technology to reduce motor noise to a silent state, allowing it to operate in an extremely quiet environment.
Avoid Losing Steps and Jittering
TMC2209 stepper driver uses SpreadCycle high-dynamic motor control chopper to control the motor to run more stably and without jitter, effectively avoiding problems such as deviation, step loss, and failure caused by chip overload.
Excellent Heat Dissipation
BTT TMC2209 stepper motor driver uses CoolStep current dynamic control to save 75% of energy. It has a large area heat dissipation pad to reduce the temperature of the driver during operation.
STEP/DIR Mode
BTT TMC2209 support STEP/DIR mode. Select working mode MS1, MS2, configure the micro-step resolution of stepper input. For detailed settings, please refer to TMC2209 V1.3 Github manual for settings.
UART Mode
TMC2209 stepper motor driver defaults to UART mode. If you use the 5th pin as the UART pin, you need to remove the resistor and solder it to the two pads below.
Potentiometer Adjustment
Turn the potentiometer clockwise: reduce Vref to reduce the driver current, turn it counterclockwise to increase the driver current.
TV
2025-09-03 14:07:15
I am not an expert with these types of motor controllers. I first bought a Synthetos shield but was noisy.When I went to build a second device, they were out of stock so I ended up buying a CNC shield off Amazon with some other motor drivers.. It was a disaster, never worked right, was noisy when it worked, was missing steps, caught fire once, ended up shorting out and blowing up my laptop.Then I bought a set of these. I had to remove the two extra pins for diagnostics, because they were in the way of the CNC shield’s own pins. This was easily achieved by heating up the solder joints, and then pulling out the pins.With that being said, I plugged it directly into the CNC shield, and it was instantly working correctly, with no missed steps, and very quietly.. much quieter than the other motor controllers and much quieter than the G shield.I highly recommend these motor drivers
Timothy A Stiel
2025-07-25 11:14:57
These little guys work good. Prices seemed to have jumped a little.
James Houghton
2025-06-18 16:03:36
So I have to say right out of the gate that Biqu was great about replacing the motherboard on my printer when it failed. The failure also caused the print head/hotend to gum up real bad and it was pretty well ruined, and they replaced that as well.When swapping out the stepper motor drivers I likely ruined one unless it got damaged when the motherboard failed. Either way, I ordered these on my own to replace the ones that came with the original motherboard.THEY WORK GREAT! They literally are plug and play and my stepper motors are super silent. If you want to upgrade or just replace failed stepper motor drivers, these are an excellent choice.
James J. Collom
2025-05-31 17:02:07
I really like these BTT 2209's. They are a bit less expensive on Amazon than most 3D printing stores but are the exact same product you would buy.
Greg
2025-05-15 17:33:49
Would recommend
alwaysbroke
2025-04-16 13:34:29
This stepper driver was to replace one on a functioning 3D printer. The existing one was a 8825 for the bed axis. I was getting overshoot at high speeds, and thought a larger motor with a driver that could handle more current would help. So far, I replaced the driver, but not the motor yet. I had to change a jumper setting on the board, so the steps would match my existing setup, as the 8825 used the jumpers in a different config. It works well, and made that axis of the printer much quieter. However, it actually doesn't hold as well as the 8825 did. I tried adjusting the current, but would still lose steps at high speeds, where the 8825 could still hold. I had to adjust my jerk speed down some for this driver, and it is smooth and quiet, but was hoping for more on the holding power. Maybe with a new motor, it will do better. If you're looking for a cheap upgrade to really cut down the noise, then this is for you. I wasn't concerned about noise, just looking for something that could handle more current.
David McFarland
2025-03-18 12:01:22
A great choice for a stepper motor driver. They reduce printer noise well and you can use sensorless homing with them.
Matt
2025-03-17 17:51:57
Got these drivers on time, and they work perfectly with SKR 1.4 turbo and ender 3.
James. S
2025-03-06 11:40:06
Super smooth stepper movement and so much quieter than the stock ones in an anycubic chiron. (Went from 68 decible noise during printing down to 42 decible!.. the silence is golden!!!) Also have been able to increase my print speed by 20mm/s.. only pain was to set the vref (i didnt install in uart mode) but that was my choice to install that way.. should have upgraded to these on day 1
Roberto Aguayo
2025-03-04 13:57:12
Funcionaron muy bien para una two trees bluer
Harold
2025-03-02 18:44:39
Used these to upgrade my Anycubic Mega X. Easy to change out and configure following what others have done on YouTube. Reversing the board connectors are the most challenging part, but if you take your time and be cautious it’s not that difficult. My printer is dead silent now, I just can’t believe why these wouldn’t be stock parts right from the start! It made a good printer into a great printer!
Mo
2025-02-05 14:34:36
Ran in UART for my voron on an octopus. Loves it.
Barry Black
2025-02-04 16:01:04
They work as direct replacement on my 3D printer but require better instructions to utilize the special features
Recommended Products