Your cart is empty.
Your cart is empty.The Bosch SP0F000049 is a Style Line 2" Electrical Water/Oil Temperature Gauge. It features a range of 100-280 degrees Fahrenheit. Requires hook up wire. Includes sending unit with 1/8" NPT thread and 1/4", 3/8" and 1/2" adapters. The gauge is a standard 2" black dial for a 2-1/16" opening and features a black bezel with removable black mounting panel. Includes mounting hardware and 12 volt internal back lighting. Only for 12 volt negative ground systems. The Style Line features a clean easy to read look with a bright pointer against a white or black background. Bosch is known for precision, engineering, and innovation. Add style and you have the first-ever line of Bosch gauges, including replacement tachometers, speedometers, temperature and pressure gauges for all applications. Bosch Branded Gauges represent the latest in design following our 100+ year history of Automotive, Industrial, and Racing products.
LW3
2025-09-05 13:03:43
Nice looking, works well, great that it comes with an assortment of adaptors for the sensor
KLH
2025-09-02 15:54:20
Took about an hour to install and I'm not fast. Much more accurate than the non-linear VDO gauge I replaced. The only complaint I have is that they didn't have a diagram of the back of the gauge with wiring. (A picture is worth 1000 words.) The written instructions were clear though. The terminal labels could have been better, also. Just shallow indentations.
PCole
2025-08-26 10:43:28
I installed this on an early 90's cummins that is installed in a 107 year old fishing boat. The installation was nice and easy, and it fit into the existing threaded port using one of the included adapters. The previous indicator was a cap-tube style sensor, and it had long since failed. Because of this, I needed to source a hot and a ground that was common with the engine block (harder than you might imagine on a 107 year old wooden fishing boat) but after that was handled, installation went just fine.You are only given 1 crimp connection in the kit, and it's for crimping onto the sensor wire at the engine side. You will need to provide your own ring crimps for the other connections.I can't say for sure that it is accurate, since I don't have a good way to verify, but even if it's a few degrees off, it's good enough for my needs. My only regret is that I got the black one... shoulda gone for something with a chrome bezel, but that's on me, not the manufacturer.
KAYKAY
2025-08-07 15:36:26
Overall a good guage, I installed it in my 1979 Lincoln continental. I let the car idle to operating temperature and the guage is steady at 185 degrees F. I wish the wiring was included. But for the price it's not bad.
Keith N.
2025-07-27 18:43:29
Mounted on top of cowl. Works great.
Mark
2025-07-06 09:50:06
Started with a very cheap wt gauge and was not accurate , returned it , searched for one with good reviews, this one seemed to match that and for a good value and a reputable name, even if it is made in China along with other low cost brands of gauges , and is accurate with in 5 deb of a infra red heat gun test for comparison
Tamas Opra
2025-06-18 18:25:54
Had the gauge installed on my newly rebuilt engine so I can monitor the coolant temperature. Shop installed it closest to the thermostat. While gauge reads 210 we measured 161 at the sensor. Can the manufacturer make this right?Thanks
Sammie
2025-06-09 13:04:23
Using my Bosch SP0f000049 Temp Gage for a Transmission Temp Gage.Got it mounted today. Checked the Gage with my laser thermometer and was about 1-5 degrees off at various temperatures. Pretty much accurate. Used a GlowShift Universal Single Gauge Swivel Pod to mount it on the left top of my Wrangler dash. Gage fits well and easy wiring except for the light. Haven't found where to hook up to my dimmer wire. I used Anderson Metals Brass Pipe Fitting, Barstock Tee, 3/8" x 3/8" x 3/8" Female Pipe and 2 of Anderson Metals 57001 Brass Hose Fitting, Adapter, 3/8" Barb x 3/8" NPT Male Pipe. The Gage kit comes with several Brass adapters. I used the 3/8 adapter to screw the sensor into. Tapped into the 3/8 rubber hose on the trans output line. Unit MUST be grounded for the Gage to work. In the photo you can see the Blue electrical ground eye, 14-16 Gage under the sensor with a 3/8 washer to take up the slack for tightening. Grounded it to the frame.I Would do it again
Richard from Saskatoon
2025-06-01 12:03:29
The temperature gauge in my 1993 Accord died so I decided to try out this gauge. Installation was straight forward. Being an electrical gauge I ran a simple wire through the door jam from the gauge to under the dash. Gauge worked properly for a few days then the gauge needle started to vibrate. I checked all of the connections which were a bit loose, tightened them up and the gauge was fine.
Sergio Fabián Ruvalcaba Bañuelos
2025-04-17 18:49:26
Excelente producto
Shopper 2000
2025-04-10 18:40:03
works great and accurate i put the green silicon cover on the bulb to make the light green wish they came with them but i had one so no worries
Customer
2025-03-26 10:53:26
works good for now
Dwayne Remraf
2024-12-09 15:35:32
.
Recommended Products
