Your cart is empty.
Your cart is empty.Product Description
Bottle Jack Axle Adapter
Heavy Duty Bottle Jack Axle Adapter is made out of high density steel that is galvanized with color zinc to prevent corrosion and rust
Compact Design
This saddle fits perfectly on any bottle jack with a 1 1/2-inch lifting platform or smaller
2 Inch Cut Outs
Bottle Jack Axle Adapter | Jack Axle Adapter Lifting Saddle for 2Inch Axle Tub for bottle jack accessories
3 Inch Cut Outs
Bottle Jack Axle Adapter | Jack Axle Adapter Lifting Saddle for 3Inch Axle Tub for bottle jack accessories
Rob T
2025-08-01 14:59:25
Got this for my honda pilot after realizing my bottle jack was too tall for the jack point when the tire is actually flat. This is very heavy, looks like it's made of a good steel. Clever design for multiple size axles. Fits well on my bottle jack, tried it once briefly, and it worked like a champ. Great to toss in your trunk as a way to potentially lift both sides of your vehicle or if you have issues with your jack point.
itbebrndn
2025-07-26 14:38:28
The fit on this is absolutely perfect. It works great. It's extremely well built, and the function on it is exactly what you need.It fits on top of the jack, and then across the bottom of the axle, can you Jack it up with very good stability? This is a great piece to have 4 jacking up your car or anything. Along that lines, it works excellent across the bottom of the axle, and it's very stable, highly recommend it
AnitAZ
2025-06-28 13:43:42
9-19-24 Good addition to lessen a little bit of anxiety when jacking up my jeep for a tire change trail side. Unfortunately this only works on the rear axle, there's not enough room to accommodate this on the front axle. I'll still just have to use it without the saddle on the front. If you're like me and have a lifted Jeep with big tires you already know there isn't a high lift jack that you can fit on your Jeep tall enough, without sticking up or out, to lift tire while the suspension droops, a hi lift jack only lifts the body and, trust me even if you do pack a tall enough hi lift jack, you should be scared at how high and unstable the Jeep will be to lift that tire. If you haven't experienced this, you don't take your Jeep off-road. You will need a bottle jack under an axle to lift the tire and not the entire vehicle, and this axle saddle makes it a bit safer. This has a load limit of 10,000 lbs. That is what the label on the box says but there is no imprint of this information on the saddle itself. It has it's place, but not a good fit on all 4 corners of my Jeep, but can be used on other vehicles. Hopefully my written and photo reviews are helpful, Thank you!
Djboomboom31
2025-06-18 15:55:28
Got this for my Lifted Jeep JK.I have a bottle jack and needed a safe way to jack up my jeeps tires to change out my breaks. Using a high lift jack was not a safe option, so I was looking for a way to use my 10 ton bottle jack for my jeep. I found this little adapter and thought it would be worth a shot.It fits on my bottle jack no problem, and allows you to safely jack up my jeep by the axle.It's well made and fit perfectly. Very pleased with this adapter. 5 Star product!
OCD_OBD
2025-06-16 10:25:21
I've been using drilled out hockey pucks for the bottle jack and have been wanting something a little more substantial. So I saw this one and figured I'd give it a try.The inner tube diameter is just about a quarter inch wider than the diameter of the head on the bottle jack. So there's not issue with it being too small.The welds around the circumference are not the prettiest. I would even say it's a bit on the sloppy side.The powder coating is not complete. There are some narrow gaps along the inner edges along the bends. I would have like to seen this without the power coating to better inspect the welds.I'm using with a jeep JT that has a 2.5" axle tube diameter. The 3 inch cutout works just fine.So it may not be the highest quality when it comes to fabrication, it does the job.
Mr68K
2025-05-10 15:01:49
This is a very well made weldment. The only issue I see is that it is advertised for any jack smaller than 1.5", but that is just not going to happen. It requires some bushings or maybe steps to do this safely. I was expecting it to come with bushings to accommodate a 1"It is a bit too expensive to be so basic in my opinion. If you are going to make an adapter and sell it for $40, at least send along a 1" bushing, and better yet a 7/8, 1" and 1-1/8 bushing.
Shop-a-Holic
2024-12-20 10:12:10
I actually got these to help jack up a corner of my porch so that I could replace a pole. These are very sturdily made. I made a very thick steel and I think they’re going to work for what I need them for perfectly. It’ll definitely give me a lot of stability and I won’t be worrying about it slipping off of the little head of my bottle jack.
Amanda and Dave
2024-11-19 17:28:33
Like many other people, I carry a large bottle jack in my fifth wheel RV so I can change a tire should the unfortunate need arise. Bottle jacks have a huge downfall that they only have a 1-1.5" diameter pad to lift with. It is nearly impossible to find a flat surface to lift on the axles of the RV. That is where this handy tool comes in. This jack adapter has a recess to fit over the jack pad and has a cutout "box" attached to cradle the axle tube to lift. The adapter has cutouts for 2 size axle tubes. The quality is very good, the welds are clean and the finish is a nice black. This adapter is well worth the cost and worthy of 5 stars.
Recommended Products
$48.99
$ 22 .99 $22.99