Your cart is empty.
Your cart is empty.Your Jeep Wrangler is made for getting off the beaten path. So make it stand out from the crowd, with custom-built Trail Armor(R) from Bushwacker. Trail Armor(R) combines trail-proven toughness with state-of-the-art Dura-Flex(R) 2000 TPO material for a look all its own. Dura-Flex(R) 2000 TPO is our proprietary automotive protective material, ruggedized for extra durability and flexibility. Unlike steel, it can’t rust. And, unlike lesser products, it’s 100% UV protected to prevent chalking. We make everything right here in the USA, designing to the tightest tolerances for a factory-like fit. Yet, you install Trail Armor(R) in minutes with automotive-grade 3M (TM) adhesive, no drilling needed. Like all Bushwacker products, Trail Armor(R) is backed by our Limited Lifetime Warranty. Your Trail Armor(R) starts out looking tough, and lives up to its looks year after year.
Stetto
2025-09-01 12:12:14
Went on easy and look great! Covered rust points I didn’t feel like fixing, which is exactly what I was going for!
Kuma Style
2025-07-31 15:10:50
This is a great kit whether you're using it for overing up blemishes on the corners or just want it for a different look in general. Installation is quick, but I'll lay out a few hiccups you may run into:1.) Make sure to buy the kit that's appropriate for stock or the bushwacker-style fenders. They're shaped differently and won't line up correctly with the wrong fenders.2.) The wiring harness connecting the passenger's side tail light is significantly shorter than the drivers side, so it's not long enough to pull through the hole and disconnect. You have to accesss it from under the car which is easy; there's a plastic or rubber panel at the end of the wheel well with a flap that comes loose ans you can bring the harness down from there and unclip. Easy, but keeps it from being a 0 dirt job since you'll have to be on your back if you don't have a relatively high lift.3.) Wash the corners areas and dry completely befor applying.4.) Do a test alignment before peeling the tape layer to get an idea. From there, align the holes first before pressing down becausebecause the automotive tape is very sticky and bonds that s moment. The driver's side is harder to line up some you have the gas cap holes as well on the side. I had success when i did gas cap homes first then lined up the back tail light and license bracket ones. 5.) It comes with clip-in adapters for the license plate screws. Make sure those are in the box before even starting.Included a before and after pic. I really like it. The armor across the tailgate is from rugged ridge.
Nick Rowland
2025-07-22 12:45:38
Look and fit nice but the double sided tape let go after a week and the holes for the license plate inserts were to big to hold so they just spin when threading the screws in.
John V
2025-07-11 13:13:54
Nice finishing touch
Dennis E Adams
2025-01-27 13:02:55
Although the Amazon "does it fit" says that it will fit a 2Door Unlimited (2003-2006) - it will not. They probably fit the standard TJ just fine. I looked on the Bushwacker site, and they don't claim it will work on an LJ (which is a TJ Unlimited) - so the issue is with Amazon's program for checking fit. Since the problem is only that the fuel door opening does not line up due to the extended body (not even close) - I may just cut them down since I already have the door center piece and the two front ones installed and really like those. My jeep will look odd if I don't have these installed, and I don't want to rip off the pieces already installed. Note that this rating is only because they don't work on my vehicle which was indicated they were - and I now have all the other pieces installed. Otherwise the piece looks great and install easily.
Gigabyte
2025-01-20 13:57:24
good quality product, easy to install, clear instructions.
Paul Wysocki
2025-01-02 12:08:46
The right side armor could be 1" wider to butt up to the tailgate hinge. It was necessary to loosen 3 screws on the factory armor above the tires on both sides to slide the corner armor under to avoid cutting. Happy with the look. Getting compliments on the new look.
Rynsey
2025-01-01 20:23:07
Works great, take your time with install and really line up the holes. I had to file the taillight wiring on the driver side hole as there wasn't enough space to fit the plastic wiring harness into the hole. TAKE YOUR TIME its worth it.
Recommended Products
