Your cart is empty.
Your cart is empty.Product Description
Fitment Type
- Fit for under and over 80ft width boats
- Fit for under and over 80ft width RVs
- Fit for under and over 80ft width trailers
CZC AUTO 12V LED Low Profile Submersible Trailer Light Kit
Complete Trailer Light Kit with Everything You Need
Come with tail lights, wires, license plate bracket, screw bag, instruction. Buy one, get all you need.
- 2 combination running, stop, tail, turn signal, license plate illumination rear lights
- 1 23ft + 2ft split Y-style color coded harness, with 4-pin male and female connectors
- 1 plastic license plate bracket
- 1 mounting hardware bag
- 1 assembly and operating instructions
Submersible and Waterproof
Please note: these trailer lights are sealed from PCB rather than the outer housings. The water can go into the housing and there are gaping holes on the housing for water to flow out.
All LED Tail Lights
Super High visibility and Longer Lifetime LED advantage! 100% comply with DOT standards. Left LED Light have 22 diodes: 12 diodes at front ,6 diodes on side and 4 white diodes facing down for license Plate illumination. Right Light have 18 diodes: 12 diodes at front ,6 diodes on side
Tail Light Size
Each rectangular tail lights with size 8" Length, 2-5/8" width, 2-7/8" height are equiped with stainless steel hardware for under and over 80" marine towing vechiles.
Wire Connection
Connect the BROWN wire of the Trunk Harness(4)to the towing vehicle's Running Lights wire. Connect the YELLOW wire of the Trunk Harness to the vehicle's Left Stop & Turn light. Connect the GREEN wire to the towing vehicle's Right Stop & Turn light. Attach the WHITE GROUND wire to the towing vehicle's frame When connect the wires, please especially note the white ground connection. Please insure the lights are really connected to the ground and form a closed cycle.
jimbo
2025-08-08 17:59:46
Perfect set work great a must buy if you need a set
Rollin C. Justen
2025-07-25 20:46:52
I installed these LED lights on a RESPO box trailer that had incandescent light bulbs.The incandescent light bulbs were failing due to poor connections in the lamp sockets.These LED type trailer lights work great.They were easy to install but required drilling holes.Because these use carriage bolts which have an upper square portion that stops the bolt from spinning when tightening the nuts, the drill bit should be a little larger than the square portion. This allows the square portion to be pulled into the hole and thus the light will be tight to the trailer.
Mark W
2025-07-07 18:22:12
Bright LEDs. Fit perfectly on my 30 yr old trailer.
Anthony F.
2025-06-19 11:52:23
I like the lights and the delivery was quick. However, after two months of use, the right light stopped functioning properly. After trying to reconnect the wiring, I realized that the sealed light has failed and is half filled with water. After drilling a drain hole and vacuuming the water from the light housing, I was able to get ~10% of the lighting to return. This temp fix will not last long. If possible, i would like to have the seller send me a single light to replace the one that failed.UPDATE: Company was very responsive and sent a new set of lights within one week of my comment. So far so good with performance. I hope the new lights are submersible but the company backed up their product.
Gerald L Green
2025-06-08 12:09:34
Great set of lights.
Julia Cunningham
2025-06-04 11:41:29
I installed these lights on a dual jet ski trailer since the old lights were falling apart. These lights are plenty bright and installed reasonably easy. Most problems were due to the trailer design. The lights don't seem to be affected by the water when launching and retrieving the jet skis. I made a 3200 mile trip across the country pulling this trailer through some snowy and icy conditions and the lights worked well the whole trip. I didn't use the included license plate holder since it is plastic and I have a metal one for my trailer.
Paul
2025-05-24 09:17:18
I put these on my mototote carrier and used it this weekend. Good lights. I still need to figure out a way to hard mount them. So far they are ziptied. Very bright at night. I suggest you solder all the connections and not use the cap nuts. For the ground, I used wires that I cut and solder them into the 4 pin ground connector. Since they are too long for my application. Kit comes with everything. I did not used the other end since I haldy have a kit on the car and just used a 7pin to 4pin adaptor.
Touchdown tg
2025-05-10 14:15:42
Used on my boat trailer works great
Procinctu
2025-03-18 16:58:06
The LED lights are bright. Water proof sealed unit. Easy to install
Tury
2025-03-11 12:19:54
Buen producto
jon
2025-03-08 15:22:50
Works great, only thing I found was the plug that goes to the ground of trailer in front to frame of trailer to short, just cut extra and made it longer. Trailer is a single axel 22 foot trailer and was lots of extra wiring left over.
Kevin K.
2025-02-25 10:29:31
Lots of plastic, so careful there, get rid of the blue wire connectors and Saulder connections, otherwise good and less expensive
Justin Davidson
2025-02-11 09:47:27
Perfect for our boat. Lights are as described. Extremely easy to install! Will most definitely buy again for our other boat when needed.
Recommended Products