Your cart is empty.
Your cart is empty.These sturdy nylon electric fan and transmission cooler installation kits include 4 plastic rods, 4 clips, and 4 foam mounting pads to provide a solid trouble-free and installation-friendly method of securing an electric fan, transmission or engine oil cooler to any vehicle.
scott
2025-09-02 14:39:07
2 ways to buy a pair of spals. Two bare fans or two fans and a kit. Didn't need the entire kit, but did need these.. They did the job.ðŸ‘
david sudano
2025-08-29 12:43:26
Very handy and useful for attaching an aftermarket cooler to my stationary air compressor.
Ryan
2025-08-25 17:23:42
Purchased a hayden transmission cooler for my tacoma and a year later needed to replace the radiator. Bought this product to re-mount the cooler to the front of the new raditor. They where just like the ones that came with the hayden cooler kit. Just be careful because once you clip them on they are on.
Scott
2025-07-22 17:56:38
This does the job and holds the cooler securely in place. However it is not reusable, so if it becomes necessary to remove the cooler, you’ll have to purchase another set.
Curious Cat
2025-07-19 15:28:42
Installed a Spal fan using these plastic rods. Have been holding for about a month with no problems. Easy to thread through the coil and radiator. Just use a soft touch and roll the posts back and forth for easy pass through. It will find its path - do not push forcefully or it may damage the coil/radiator. Highly recommended. Good quality. Not super high quality but good value.
David M.
2025-06-30 11:25:39
This will be used to hold my air compressor air cooler to the screen that surrounds my compressor belt drive
John Wycoff
2025-06-25 13:58:53
Was not able to use, due to the air conditioner condenser .
Doug Carrington
2025-06-05 16:07:34
Quality mount
scott
2025-04-06 11:36:02
2 ways to buy a pair of spals. Two bare fans or two fans and a kit. Didn't need the entire kit, but did need these.. They did the job.ðŸ‘
david sudano
2025-02-16 12:53:05
Very handy and useful for attaching an aftermarket cooler to my stationary air compressor.
Ryan
2025-02-14 14:42:25
Purchased a hayden transmission cooler for my tacoma and a year later needed to replace the radiator. Bought this product to re-mount the cooler to the front of the new raditor. They where just like the ones that came with the hayden cooler kit. Just be careful because once you clip them on they are on.
Scott
2025-02-11 15:05:11
This does the job and holds the cooler securely in place. However it is not reusable, so if it becomes necessary to remove the cooler, you’ll have to purchase another set.
Curious Cat
2025-02-06 18:40:05
Installed a Spal fan using these plastic rods. Have been holding for about a month with no problems. Easy to thread through the coil and radiator. Just use a soft touch and roll the posts back and forth for easy pass through. It will find its path - do not push forcefully or it may damage the coil/radiator. Highly recommended. Good quality. Not super high quality but good value.
David M.
2025-02-04 14:09:38
This will be used to hold my air compressor air cooler to the screen that surrounds my compressor belt drive
John Wycoff
2025-01-31 14:28:14
Was not able to use, due to the air conditioner condenser .
Doug Carrington
2024-11-27 09:53:10
Quality mount
Recommended Products
$60.71
$ 24 .99 $24.99
$52.77
$ 23 .99 $23.99