Your cart is empty.
Your cart is empty.Product Description
DROK Timer Relay With LCD, it deserves your attention
LCD Display
The screen can clearly display the working mode and parameter.
Functional buttons
It is easy to set parameter. Moreover, there is a key emergency STOP function (STOP key), and with the reverse connection protection, reverse connection will not burn the relay.
(More information, please check the User Manual. PDF from Product information---Technical Specification.)
Micro USB 5.0V power supply is available
Working voltage: DC DC 6-30V
Input port: Micro USB 5.0V
Wire sockets
High trigger level: 3.0-24V
Low trigger level: 0.0-0.2V
Christopher Dejlitko
2025-09-03 13:41:09
I purchased this to use in a round counter for a reloading press, the signal from my proximity sensor was too fast for my counter to see so by adding the relay with a 1 sec delay it worked perfect.Very easy to setup the program and I had it up and running in minutes.I am already looking for more uses for this relay and will purchase more in the future.
Stas Stasevich
2025-08-09 11:43:01
Lots of mode options. I used it to interlock an ERV system into the AC thermostat. The ERV could only accept a pulse signal and not a dry contact, hence the pulse timer is needed. Works great in the attic. We will see how well it handles attic temperature in summer.
Jason A. Lari
2025-04-30 13:21:46
The media could not be loaded.
mark .l.o.l. twain
2025-04-17 10:58:01
timer 1(t1): reviewed item; timer 2(t2): pictured instructions(sold also on Amazon). t2 has 10 settings: 0-9. t1 has 7:1-7, but can achieve almost all as t2 by switching physical wires on open and close relay connections. t1 came with no instructions. important note is timer range: after entering set mode(long press set) short press set to op/cl blinking short press stop to change timer range. you'll notice the decimal place changes with each press signifying count by seconds, minutes etc. i accidentally set to minutes and waited for the timer to count down seconds which never happened. thought the timer was broken and went to the second of my 2 pack and it worked fine. then i found t2 with instructions and reset first "broken" t1 to seconds and it worked also. t1 comess with a dedicated 5v micro usb port. t2 accepted 5v although it says 6-30v. t1 short press stop can disable/enable (off/on) the timer from executing(i found no off button for t2). t2 short press stop is used as a trigger for most settings(t1 only setting 6). both use long press stop to set display to auto off after 5 minutes on certain settings.
TStien
2025-03-10 11:02:29
When I purchased this, it took me a while to figure out. After extensively going over the instructions and reading other people's reviews I was able to figure it out. Had to mess with it for a little bit until I could get my bearings straight. Once I did though it worked great and as intended.
Albert C.
2025-02-12 15:14:51
I'm using this for a hunting decoy project and it's working out great. I have it on the P6 setting to start its on/off sequence right when it gets power. I have a wireless remote set up to allow power to it so essentially I have this relay set up to run an on/off cycling program via remote control...in a very small package. I plan on making about 8 of these so will be buying more soon.
jorge b.
2025-01-08 10:07:10
Está tarjeta de control funciona excelente para cualquier sistema que necesite automatización de encendido o apagado, yo lo uso con un sensor de flujo para una bomba de agua mucho mejor que un sensor de presión, según yo, en mi caso perfecto
macmike100
2025-01-01 18:47:51
This timer works as stated. The problem I had with it is that every day was a slightly different time. It seemed to run slow. It was off by about 5 min per day. I therefore would not recommend it for a daily repeating event that you would want to be an exact time. It has many good functions but the time keeping made me replace it with another brand. All other functions work fine.
Recommended Products
$41.85
$ 18 .99 $18.99