Your cart is empty.
Your cart is empty. DUROCK Plate Mount Stabilizer V3 Highlights
Innovative Design 1: Elastic Support Base Inside Stem / Slider
Innovative Design 2: Smaller Wire Gap
Innovative Design 3: Angled Snap / buckle of Housings
Advantage: Minimize Wire Wobble and Noise
Compatibility: Min to 1.2mm Plates
Style: Cherry MX Plate Stabilizer Style
Housing Material: POM
Stem/Slier Material: POK
Wire Color: Stainless Steel
Package included:
7 x 2u Stabilizers
1 x 6.25u Stabilizers
1 x 7u Wire
Stanton Nichols
2025-09-03 10:44:39
These stabs are really solid! Even without lube, they rattle much less compared to the stock stabilizers in the Ducky One 3. However, after some break in, I found that they needed some lube to STAY quiet.Still better than the stock. Solid mod, definitely a good choice.
Electrodude
2025-08-20 12:42:36
These worked perfectly for my 3D printed keyboard, they feel perfect. I will probably use these on my other keyboards as well. Definitely recommend for plate mounted cherry style stabilizers.
Dustin
2025-08-05 19:36:49
If you have a hot swap keyboard, these are the best option. The only time I will ever use screw in stabs again is if I had not plate. Because these plate mount stabs are so much better than screw in stabs in every way. I didn’t think these would install so well. They are rock solid and the best part is you don’t have to remove all of your switches and take off your plate every time you need to tune your stabs or replace a stab.This is the best thing since sliced bread.
Chris
2025-08-03 15:09:47
These sound great with some lube and grease! Wish they fit on my Luminkey plate, definitely check compatibility if you can.
Rico Suave
2025-07-29 12:16:22
I bent my stabilizer being a complete noob and these were and easy replacement
darrelltx
2025-07-15 11:11:53
Replacing the stock stabilizers for my Redragon K556 turned into a mini-saga. The PCB won't support screw-in, PCB-mounted stabilizers, so your choices are limited to the plate-mounted variety.Unfortunately, most plate-mounted stabs are tailored for 1.6-mm thick PCBs. The K556 utilizes a 1.2 mm PCB. These Durock V3s will work with either. Definitely an improvement over stock, which tended to "lean" to one side or the other. These stabs keep the keycaps flat and at the appropriate height.I lubed mine with dielectric grease and have no complaints so far. They were easy to install, as well. Only criticism is Durock refuses to include any sort of instructions with their products--not even a link to a webpage. Fortunately, there are online resources available.Strongly recommend.
Lucas
2025-06-30 18:15:55
I was able to fix several keyboards that had 1 or 2 problems here or there. One keyboard i bought had terrible reviews regarding the shift, tab, and space bar having issues with the original stabilizers causing them to get stuck. i popped these in and it made that $35 keyboard feel like $100 keyboard. Will use this product from here on out!
Andrew Paschall
2025-06-23 11:36:41
Completely eliminated all rattle in my keyboard even before lubing. Definitely a pricey product but 100% worth it for me.
Stanton Nichols
2025-06-07 16:54:49
These stabs are really solid! Even without lube, they rattle much less compared to the stock stabilizers in the Ducky One 3. However, after some break in, I found that they needed some lube to STAY quiet.Still better than the stock. Solid mod, definitely a good choice.
Electrodude
2025-06-04 16:25:44
These worked perfectly for my 3D printed keyboard, they feel perfect. I will probably use these on my other keyboards as well. Definitely recommend for plate mounted cherry style stabilizers.
Dustin
2025-05-31 17:44:38
If you have a hot swap keyboard, these are the best option. The only time I will ever use screw in stabs again is if I had not plate. Because these plate mount stabs are so much better than screw in stabs in every way. I didn’t think these would install so well. They are rock solid and the best part is you don’t have to remove all of your switches and take off your plate every time you need to tune your stabs or replace a stab.This is the best thing since sliced bread.
Chris
2025-05-28 11:13:07
These sound great with some lube and grease! Wish they fit on my Luminkey plate, definitely check compatibility if you can.
Rico Suave
2025-04-13 15:17:12
I bent my stabilizer being a complete noob and these were and easy replacement
darrelltx
2025-03-10 10:13:46
Replacing the stock stabilizers for my Redragon K556 turned into a mini-saga. The PCB won't support screw-in, PCB-mounted stabilizers, so your choices are limited to the plate-mounted variety.Unfortunately, most plate-mounted stabs are tailored for 1.6-mm thick PCBs. The K556 utilizes a 1.2 mm PCB. These Durock V3s will work with either. Definitely an improvement over stock, which tended to "lean" to one side or the other. These stabs keep the keycaps flat and at the appropriate height.I lubed mine with dielectric grease and have no complaints so far. They were easy to install, as well. Only criticism is Durock refuses to include any sort of instructions with their products--not even a link to a webpage. Fortunately, there are online resources available.Strongly recommend.
Lucas
2025-01-28 11:35:08
I was able to fix several keyboards that had 1 or 2 problems here or there. One keyboard i bought had terrible reviews regarding the shift, tab, and space bar having issues with the original stabilizers causing them to get stuck. i popped these in and it made that $35 keyboard feel like $100 keyboard. Will use this product from here on out!
Andrew Paschall
2025-01-13 16:04:09
Completely eliminated all rattle in my keyboard even before lubing. Definitely a pricey product but 100% worth it for me.
Recommended Products
