Your cart is empty.
Your cart is empty.Product Description
Hippored EasyBoot 90mm - split cv boot wheel side
PRODUCT DETAILS
EasyBoot is an Italian patent. Unlike classic spare parts it allows you to replace the worn-out axle boot without removing any mechanical part. Made of special, extremely durable rubber CUFFIA FACILE (Easy Boot) is equipped with an innovative male/female opening system and a specific seam for gluing. Thanks to its elasticity and design, it adapts to most CV joints and drive shafts of car manufacturers.
1 piece kit containing:
- 1 boots size ø 90mm
- 2 ties
- 5gr of glue
- 50gr of grease
INSTRUCTIONS Use easy boot 90mm for cv-joints with diameters from 90 to 110 millimetres and axle shafts from 24 to 29 millimetres.
INSTALLATION INSTRUCTIONS
STEP 1
- Thoroughly clean the drive shaft and place Easyboot on drive shaft.
STEP 2
- Fill the groove with the glue supplied.
STEP 3
- Attach the two parts. Wait 5 minutes for the glue to dry.
STEP 4
- Remove the old bands and cut the old boot.
STEP 5
- Place the grease supplied inside EasyBoot.
STEP 6
- Insert EasyBoot and tighten the bands supplied. And that's it!
EASYBOOT
Save time, make your life easier!
Darek
2025-09-04 12:38:02
I used it for my Nissan Altima. The glue dries quickly and after a week of installation everything is still holding. I recommend this product.
Mark P. Bunz
2025-08-31 17:54:16
Let me start off by saying it is a quality rubber boot and the adhesive bonds the seam very nicely. Once the he glue is dry I don’t think you would be able to pull the seam apart without tearing the boot in a different area (seam is stronger than the boot itself).Now the manufacturer gives you approximate sizes that your boot will fit, my cv joint is 94mm so I purchased the boot that fits 90-110mm cv joints. There is too much excess material to snug up and get a secure attachment with the bands supplied by the manufacturer. The lip of the boot would get into the grove of the cv joint but it was impossible to get the pull style band tight enough to keep it securely in place. The first time the steering wheel was turned it would have popped right off. I wound up having to purchase a few different style bands to finally get it to seal properly. In hindsight I wish I would’ve ordered the smaller boot (smaller boot is up to 89mm) and tried to stretch it over the cv joint as it was only a few mm difference.
puttone
2025-08-08 09:28:46
easy to put on
hornms
2025-07-17 14:26:38
I’ve replaced a few axles in my day but when the Lexus boots tore, I did not want to replace my high quality Lexus parts with Autozone axles (no offense). I thought I would try just replacing the boot using this product and it seems to work just fine. The kit is very cost effective, includes new grease, and new metal bands. The repair was super quick, and looks great. The glued seem looks exactly the same after 3000 miles. If your axle is still good, then I recommend this option. IMHO OEM axles are better built than those commonly sold at the local parts store.
Dad
2025-07-16 10:08:08
It was easy to install but it did not fit the shaft of our 2014 Nissan Rogue Select. The OEM shaft has three grooves that the Easyboot does not cover. I had to get a boot from a different company.
Customer
2025-07-05 10:19:13
I was NOT looking forward to removing my front axle to replace a split CV boot. I saw the Easyboot Split CV Repair Boot and decided to give it a go, I am so glad I did. The Easyboot Company has done a wonderful job with the interlocking seam and the overall quality of the CV boot in the Kit. I used a strip of masking tape to keep the interlock joint grease free while I installed the new CV Grease and then used the supplied glue to seal the Clean interlocking joint after removing the tape. This is the first CV boot that I have replaced with the axle still in the vehicle, it by far the easiest CV repair that I have done. Easyboot supplied the new CV Grease and both Stainless Steel Zip Ties in the kit, the only item I ordered with the kit was a Ten Dollar Banding tool that would work in tight spaces to tighten the Stainless Bands. I gave the Easyboot Split CV Repair Boot a Full Five Stars Across the Board. The CV Boot Kit is Complete, Easy to Use, Very Affordable, Durable, Reliable, And it saves a ton of $$$ and Time when compared to removing the Axle & Hub with all of the complications that that involves to replace a broken CV Boot.
eric gizard
2025-06-15 13:50:02
doesn't fit all shaft dimension..the concept is great, but the rubber was too small for an toyota FJCruiser..
stephgood
2025-04-27 14:39:13
I used the easy boot to buy me some time to fully replace my trucks axle. The fit was tight but it worked great. I did not use the included sliding metal straps as I had some crimp style ones handy. No issues to report. Highly recommeded!
Gallerani Carlo Alberto
2025-04-05 15:05:59
Avevo dei dubbi ma è stato facile il montaggio e fa quello promesso dopo 5 mesi di utilizzo fa ancora il suo lavoro
Leonidas77
2025-03-21 10:45:19
Souflet de cardan de la marque Hippored, en 90mm de diametre, livré avec 2 colliers métal un tube de colle et 50grammes de graisse graphitée. Pas encore installé mais semble de qualité à priori, la goulotte maintient bien la zone sectionnée une fois les deux parties emboitées.
TheBig1ITALY
2025-03-17 18:32:42
Purtroppo risultava non adatto! Controllate bene le dimensioni
Mike
2025-02-27 12:24:14
Le produit n'a pas tenu bien longtemps...
vieira
2025-02-17 13:33:53
Produit de bonne qualité, mais un peu court 100mm la moyenne a 120mm de longueur et 29 mm pour l'arbre un peu juste pour mon véhicule.
Recommended Products