Your cart is empty.
Your cart is empty.
Compatible with Honda inverter generator
EB2000I A GENERATOR, JPN, VIN# EBCJ-1000001 TO EBCJ-9999999
EB2000IT1 A GENERATOR, THA, VIN# EAET-1000001 TO EAET-9999999
EU2000I A GENERATOR, JPN, VIN# EAAJ-1000001 TO EAAJ-1036877
EU2000I A/A GENERATOR, JPN, VIN# EAAJ-1036878 TO EAAJ-1169999
EU2000I A/B GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AC GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AC1 GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AC2 GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AN GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AN1 GENERATOR, JPN, VIN# EAAJ-1170001
EU2000I AN2 GENERATOR, JPN, VIN# EAAJ-1170001
EU2000IK1 A1 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 A2 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 A3 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 A4 GENERATOR, JPN, VIN# EAAJ-1170001 TO EAAJ-9999999
EU2000IK1 A5 GENERATOR, JPN, VIN# EAAJ-1170001 TO EAAJ-9999999
EU2000IK1 A6 GENERATOR, JPN, VIN# EAAJ-1170001 TO EAAJ-9999999
EU2000IK1 AC GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 AC1 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 AC2 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 AN GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 AN1 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IK1 AN2 GENERATOR, JPN, VIN# EAAJ-2017305 TO EAAJ-9999999
EU2000IT1 A1 GENERATOR, THA, VIN# EACT-1000001 TO EACT-9999999
EU2000IT1 A3 GENERATOR, THA, VIN# EACT-1000001 TO EACT-9999999
EU2000IT1 A4 GENERATOR, THA, VIN# EACT-1000001 TO EACT-9999999
JOHN M.
2025-09-06 17:05:43
Great value and works great. Yea the plug doesn't match like everyone say's but is a no brainer for someone with any mechanical abilities to swap them out. Generator runs like new !Would definitely buy it again
Mark and Nancy Burke
2025-08-26 09:23:56
I bought this carburetor for a Honda EU2000 and it works well on it. As others have mentioned, the throttle servo connector on this carburetor does not match the Honda connector. But it’s an easy matter (two screws) to install the original Honda servo onto this unit. The other minor difference is that the included insulator to manifold gasket is a different shape than the Honda gasket, so if you can’t reuse the original, order the OEM replacement gasket. But once installed, this carburetor ran the engine well at idle and under load, so I would buy it again.
Tim Draughon
2025-05-22 17:45:09
The carburetor worked perfectly, but the throttle control solenoid had a different connector. We swapped the old one onto the new carb and it worked perfectly.
SaltwaterSlick
2025-05-17 10:19:32
These carbs do NOT work for a HONDA EU2000i generator... The "look" like the should, but as others have posted, the wiring plug is wrong, AND if you look at the carb, there are line connections all on one side of the carb... the OEM carb has the fuel inlet on one side and the vents/drain on the other side. I don't know what the internal porting of these are but I have 2 of these generators and I tried 2 of these carbs on them... Of course, I had to use my old electronic controllers and swapped that out, but both units did the exact same thing... They would fire and try to start/run, but would die right away... I then bought new fuel pumps... same thing... During this third or 4th round of installing/removing reworking, etc. that's when I noticed the ever so slight difference in the porting of these carbs... Bit the bullet and bought HONDA OEM carbs. stuck them on and my genny's run like a top... They're like brand new... I have these 2 pieces of junk boxed up for drop off at the UPS store later today. DO NOT BUY THIS CHEAP CHINESE JUNK!!
Customer
2025-04-23 09:56:59
Worked as expected , On time
David J. Willey
2025-01-09 11:59:26
good quality ,works perfect
Will lara
2024-12-30 15:13:42
The kit did not fit., the high low throttle did not connect. I did not use the kit but resided my original
Lumosvalley
2024-12-22 10:09:07
The carb is functional, but as others have noted, the stepper motor connector is incorrect for a Honda EU2000i/2200i. This is designed for a Ryobi RYi2300BTx. I was able to remove the old stepper motor and installed it on this carb. It worked well. Looking at the wiring diagrams, it looks like the yellow and blue wires match. white matches to red (looked pink) and red (old) matches to orange. I hope this helps others.
Recommended Products
$38.97
$ 19 .99 $19.99