Your cart is empty.
Your cart is empty.Product Description
Daytime running light
Turn signal light
No need to open the car headlight assembly
There are 3 cables, YELLOW RED and BLACK
- The Black connect to ground line
- The Yellow connect to turning cable - the led strip shows flowing amber(yellow) light
- The Red connect to running cable - the led strip shows white light
Smart decoder
- Quick start
- Waterproof function,
- It can enhance signal.
With sticker,can be cut
Tips for your cutting DIY installation:
- 1. Power off during your customizing installation
- 2. Make 3-Leds as a team and cut every 3-LEDs
- 3. Make sure no debris gets in
- 4. Sealing the tube with insulated glue after cutting in short，light tubes cannot be folded
Flexiable
Soft material, can be bent and can be DIY.
Waterproof
IP 65 waterproof.
Don't worry about naked light strips. It has good water resistance.
Sequential flow change
It can also be used as lightings around headlight lamp, tail stop brake light, fog light or under the bumper to give your vehicle an impressive look as LED daytime driving/running lights (DRL) such as the latest for Ford,Chevrolet,Toyota or Honda.
This LED strip light tube also can be used for boat, motor, cabinets, tables, chairs, stairs, and anywhere you want, it will add aesthetic appeal.
J. Kriezel
2025-09-01 09:19:51
Coming back to this 2 years later, and I must say these have been awesome to drive with! So honestly only one led bulb has gone out on both sides in the same place and only in blue. Not bad for two years! I will buy again when the weather warms up for it is easier to install when warm. Also I bought a role of 3m tape to apply these with, because the adhesive isn't the best that comes with them. Overall I highly recommend these rgb+turn led strips.
Chase D.
2025-08-13 15:11:56
Was very happy with the way the lights looked upon TESTING, i always test my lights when i get them. After spending hours pulling housings apart to customize them with these strips i finally get to wiring them into the vehicle. The soldering inside the control box blew a fuse and the DRL White light was inoperable. Pulled LED control box apart only top find the ground solder was held together with 1 strand of wire, the red power wire was the same way, and was stretched so far that it was making contact with the ground. EXTREMELY unhappy with the worksman ship, and now i have to take my housings back apart, use double the glue that was originally planned for, and order another set, setting me back possibly another week.EDIT: The company contacted me VIA Email and has replaced the set with a new set. Very good Customer Service as they responded only a few hours after leaving this comment, and had a new set to me within 2 days. Changing my review to 5/5, the company acknowledged they sent me a faulty part, apologized, and sent me a new part fast. Will order from them again in the future
W. Priester
2025-08-11 18:26:51
The quality of the lights themselves seem to be good. For the purpose of these lights, I'll say that the brightness is good. My bumper was already off prior to the installation of these lights, so I was able to route the light strip in a area that most people won't have access to, unless they remove their bumper. I started the LED light strip about 3" from the headlight's inner bottom corner, and from there wrapping the LEDs up and over the top of the headlights, with the end of the LED strip ending where the fender and the hood meet. The appearance was perfect, but the problem came when I put everything back together. The LED lights are in a thick plastic housing, and that thick plastic interfered with my hood closing properly. After seeing how beautiful the lights look when they start below the headlight, I did not wanna change that style. So to accomplish the same look and have my hood closed properly, I opened the headlight housing and installed the LED light strips inside them. I would recommend that the manufacturer come up with a thinner design, and stronger adhesive for the tape. The double sided tape started separating from the LED strip, but I overcame this issue with small drops of glue. If you don't need to readjust your light strips after your initial install, you may not have this issue.Other then those two things, everything else have been great so far.
Hg
2025-07-19 16:02:19
These lights look nice,seem well made but there is poor quality control or I just got a bad one,I installed them and all functions didn’t work there is clearly a short somewhere because if I wiggle wires at the box on them(I’m assuming it’s a fuse or junction box) the one that fully functions has issues too ,they are soooo cheap and inexpensive I figured I’d take a gamble and try it out,not worth the hassle of returning for a few dollars that they cost,but hey,sometimes these little inexpensive mods work well,and sometimes not,it’s worth the gamble I guess since the cost is so cheap,try it out,you may get a functional set,I would advise testing before installing though.it’s a gamble .
Corey Anderson
2025-07-13 18:45:56
Good look ....couldn't finish the install. 3 LEDs out on the first power test...these are very fragile..***UPDATE***... new set all is well. These can be a great mod to your car if you take the time and do the install to survive elements if you are mounting this outside of the headlight.1. Test - should be the first thing you do. confirm look and color.2. have on hand. a. better 2 sided tape. b. liquid tape c. Silicon RTV/Superglue/Gorrilla Glue d. Goo Gone3. handle these like crystal they are fragile!!!!!4 seal control box openings with liquid tape, build up a few layers. (after cutting I reused end caps.. added silicon and pressed it on to ends this takes a while to dry and cure.5. use goo gone to help remove installed 2 sided tape (be careful of ends.6. this also allows you to use both sides of the lights. I chose to point LEDs into the headlight bucket. the leading edge is still bright but not as good as led pointing out... test fit both ways to be sure.7. GIVE LIGHTS TIME TO DRY.. and they should last a good while.(a single drop of water and these are toast)8 done right the prep should take you 24 hrs including drying time to be safe
ckeller52
2025-07-12 17:51:11
The media could not be loaded.
Nelk2
2025-06-23 13:38:31
good
W Rene
2025-05-31 17:31:28
Couple of nice surprises. 1)The LEDs are facing out of the edge of strip, instead of facing up from the strip. This allows it to be installed in tight gaps, and easy to bend around corners.2) The amber LEDs light sequentially. I would have been happy with on/off, but having them run around is a bonus. The white Leds are bright, and true white. I installed these on the outside perimeter of my RZR headlights. Some additional adhesive was needed in the tight corners, but that's to be expected.
Eduardo
2025-05-04 14:11:31
Le da un estilo distinto a tu vehÃculo , fácil de instalar
user-MXWDEH1
2025-04-19 16:52:58
ممتاز
Jalieskys
2025-03-07 16:32:42
zuper
Essamaldinabullah
2025-02-22 15:37:26
المنتج ليس كما بالوص٠الديكودر غير موجود
andres G.
2025-01-21 15:31:31
No hace la función que anuncian el los videos cortod
Recommended Products