Your cart is empty.
Your cart is empty.
Features:
Easy to use:
You can assemble the wire according to your needs, and our LED light strip connectors can flexibly adapt to different projects. No soldering required. Just snap the prepared LED strip section into the connector to connect. Compatible with 30-120 LED/Meter strips and can support high current LED strips.
More tips:
LED adapter connector fits for the connector to work with 24V system and suitable for RGB strip lights with soldering pads, both IP20 non-waterproof and IP65 waterproof light strips. You can pierce the light bar from the back or the front. The IP20 RGB light bar is recommended to be pierced from the front of the light strip, and the IP65 waterproof light bar is recommended to be pierced from the back without removing the silicone on the surface of the light bar. If you accidentally cover the connector, you can pry it off with a screwdriver.
Please use a standard 22 AWG wire for connection. There are some unqualified wires on the market that may result in unsuccessful connection. When the connection is unsuccessful, please observe whether the clip connection contacts are in contact with the copper core of the wire. Unqualified wires may include: there are too few copper cores to connect accurately. The copper core is off center and cannot conduct current. If the wire is qualified but the connection is still unsuccessful, you can re cut a piece of wire and try to connect.
Specifications:
Material: PC
Color: transparent
Quantity: 20 pieces
Size: as picture shown
Package includes:
20 x LED light connectors
Warm notes:
Please allow a little error on the size due to manual measurement.
Please read the size instruction carefully before purchasing.
8 mm/ 0.31 inch or 12 mm/ 0.47 inches LED strips.
Small parts are included, please keep away from children under 3 years old.
Alexis
2025-08-22 14:17:16
The amount of time and effort saved just from these goobers are crazy. I don't have to fight for my life trying to solder those wires to the led strips anymore ðŸ˜ðŸ˜ðŸ˜ðŸ˜. I had to use pliers to close the side with the wires since I got noddle arms, but so far these have been working great.
Joseph McCall
2025-06-15 10:00:47
Used these with multiple strips of LED lights and the only caveat is that they do not work with silicone-coated strips (which is expected). Had no issue opening or closing, none broke during installation, worked as expected. Good value overall, recommended.
Heather D. Harless
2025-06-06 11:47:32
These initially worked great and I was happy to not spend my time soldering. We used them to install 14 strips of RGB tape into light boxes on a set. After a few days I had the Blue in one box fail at the connector, didn't think much of it so I replaced it, then over the next 2 days I have 3 more completely go out. These were static items that after install were never touched again. After I opened one of the other failed ones and removed the connector and saw that the common was completely fried I went through and just soldered the wires directly to the pads for all of them (which is what I should have just done from the start).I wouldn't trust these, they pierce through and obviously end up wiggling around enough that they don't maintain a solid connection after the initial crimp.
Jesse G.
2025-03-15 11:59:08
Let me start off by saying I'm an electrician by trade and have wired hundreds if not thousands of electrical panels from scratch. So im not new to ALL sorts of wire. As far as functionality, these connectors were very hit or miss. They wouldn't stab through into the wire enough for adequate connection and I had to bend the fingers apart a little bit to get them to hit the conductive part on the light strip. Theyre easy enough to use in principle and if you're crafty enough, you can make them work. I will probably find a different route for my light boxes next time. I guess im just used to fantastic products like wago, and expected too much. I have a bunch to use up so maybe ill have better luck next time. No picture really needed. They look exactly as shown. Picture of my project though for reference of how I used them! (:
loveserver2010
2025-02-10 14:06:39
Good product. No problem at all
Liam Devlaeminck
2025-01-17 16:55:11
They work well if you’re connecting the waterproof strips to thicker gauge rgb wire (like the multicolored ones sold on Amazon)The quality is kind of eh, some of the clips on the sides don’t fully engage and it hangs loosely, some of them clamp so tightly that you can’t pull them apart at all. Not super impressed with the quality. But certainly a good amount for the moneyThey do not work for connecting wires to more wires.
Lisa Negron
2025-01-15 11:01:21
Perfect fit, thanks, used for my kitchen LED
D. Paul
2025-01-06 10:41:55
These worked well with the GoVee strips but not the strips with densely populated neopixels in the example photo.
John F.
2024-12-13 15:49:15
The teeth aren't strong enough to pierce the casing around the wires, so they don't make contact. Using pliers to add a bit of pressure does nothing, as the amount of pressure needed to pierce the wires only cracks the housing.
Recommended Products
