Shopping Cart

Your cart is empty.

Your cart is empty.

Forward and Reverse Relay Module 12V for tarp Motor Winch Motor Trim Motor Reverse Replaces 5541100 ATP0110 Polarity Module for Marine Jack Plate

4.7 (14) Write Review
Free shipping on orders over $29.99

$29.99

$ 13 .99 $13.99

In Stock

About this item

  • [Application Widely]: the forward - reverse relay module could be commonly used as relay for tarp motor, hoists, hatches, winches, electric trim tabs, Intake/Exhaust Fans and Vents
  • [Fitment ] This Reverse Polarity Module changes the direction of the motor when triggered rated at 12 VDC; Product common use: Tarp systems, truck winches, boat jack plate lifts, reversing motor application.
  • [Reference Interchange P/N]: CH 24452, K10746M, 13994, 5541100, ATP0110
  • [Spec,]: Heavy duty 80A at 12VDC for Intermittent Loads, 50A at 12 VDC for Continuous Loads. Wiring terminals and instruction are included in the package.
  • [Spec,]: The Motor Reversing Relay features also Brass studs and hardware for corrosion and moisture resistance; WATERPROOF: Sealed, Potted, IP67 rated;


TREXFLOW Supply Premium Quality Forward and reverse relay module.

If you have a motor that needs to operate in both directions, this relay module is what you’re looking for.

The Most Common Uses:

  • Lift and Tarp applications
  • Hoists
  • Hatches
  • Winches
  • Electric Trim Tabs
  • Intake/Exhaust Fans and Vents

SPECS:

  • WATERPROOF: Sealed, Potted, IP67 rated
  • MADE FOR SALTWATER: brass studs and hardware for corrosion resistance
  • Runs 70A at 12VDC for Intermittent Loads
  • Runs 50A at 12VDC for Continuous Loads

You may also see this module referred to as a Reverse Polarity Module, Motor Reversing Relay Box, or a Forward-Reverse Relay Box. It’s all the same thing!


Christopher Moreno
2025-09-05 11:33:16
Replacement part for 2013 Gatortail works great.
kenneth bollinger
2025-08-29 16:00:36
If they want put the sate of the dry Contac's with power on the coil put on the add deenergized nc or or energized no that would help i thing . For some that might not know out of the box dry contacts term 30 to 87a nc from 30 to 87 no .
Bcon
2025-08-28 17:25:02
The relay works great, I have it installed on a lift table that I fitted with a motor so that the height an be adjusted with a switch. Works great!
Warren
2025-08-23 17:07:05
Wiring diagram shows control switch wired to 12volt +. It should be wired to 12volt-.
Brandon
2025-08-19 11:54:07
Very nice relay module, exactly as described, and performs as expected.
Christopher Moreno
2025-08-12 11:16:02
Replacement part for 2013 Gatortail works great.
kenneth bollinger
2025-06-21 14:37:24
If they want put the sate of the dry Contac's with power on the coil put on the add deenergized nc or or energized no that would help i thing . For some that might not know out of the box dry contacts term 30 to 87a nc from 30 to 87 no .
Bcon
2025-06-19 10:44:45
The relay works great, I have it installed on a lift table that I fitted with a motor so that the height an be adjusted with a switch. Works great!
Warren
2025-05-29 18:17:59
Wiring diagram shows control switch wired to 12volt +. It should be wired to 12volt-.
Brandon
2025-04-28 18:40:32
Very nice relay module, exactly as described, and performs as expected.
Sally Lockhart
2025-04-26 15:49:56
I'm building a camper van and I built a lifting bed using four large linear actuators that raise and lower the bed from the ceiling down to couch level. They each draw about 10 amps of current and I need them all to operate at the same time, so I didn't want to just use a switch feeding all of them.This unit is just the ticket. I use a small 12v rated switch to control it and it operates the actuators, reversing the polarity to raise and lower them. It has no problem with the 40 amps of current.The instructions are clear and straightforward, once you get your head around what is going on. One tricky bit is that the control switch operates by grounding one lead or the other, not by applying voltage to them. Once you figure that out it makes a lot more sense.It solves a particular problem and does it well at a fair price, nice piece of kit.
Holliday
2025-02-15 15:46:03
Update - posted pics after install and still working great on TH marine outboard jackplate!The unit worked very well for a replacement solenoid on a motor jack plate. All the electrical internals are fully encapsulated and waterproof.
Sally Lockhart
2025-01-19 11:56:24
I'm building a camper van and I built a lifting bed using four large linear actuators that raise and lower the bed from the ceiling down to couch level. They each draw about 10 amps of current and I need them all to operate at the same time, so I didn't want to just use a switch feeding all of them.This unit is just the ticket. I use a small 12v rated switch to control it and it operates the actuators, reversing the polarity to raise and lower them. It has no problem with the 40 amps of current.The instructions are clear and straightforward, once you get your head around what is going on. One tricky bit is that the control switch operates by grounding one lead or the other, not by applying voltage to them. Once you figure that out it makes a lot more sense.It solves a particular problem and does it well at a fair price, nice piece of kit.
Holliday
2024-12-22 12:16:14
Update - posted pics after install and still working great on TH marine outboard jackplate!The unit worked very well for a replacement solenoid on a motor jack plate. All the electrical internals are fully encapsulated and waterproof.